The display ie handling can be controlled independently in the send and
receive directions with the following options:
* Block display text data.
* Use display text in SETUP/CONNECT messages for name.
* Use display text for COLP name updates (FACILITY/NOTIFY as appropriate).
* Pass arbitrary display text during a call. Sent in INFORMATION
messages. Received from any message that the display text was not used as
a name.
If the display options are not set then the options default to legacy
behavior.
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@2190 2fbb986a-6c06-0410-b554-c9c1f0a7f128
There currently exists a pri_new_cb() API call that allows you to create a
PRI with user-defined I/O read and write callbacks, and option userdata.
Add the same capability for BRI interfaces by adding a pri_new_bri_cb()
API function.
(closes issue #16477)
Reported by: nic_bellamy
Patches:
pri_new_bri_cb_api.patch uploaded by nic bellamy (license 299) (with minor cosmetic changes)
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1836 2fbb986a-6c06-0410-b554-c9c1f0a7f128
This feature passes ETSI AOC-S, AOC-D, and AOC-E message information to
the upper layer (i.e. Asterisk) for processing.
Relevant specification: EN 300 182
Consideration was made for the possible future addition of Q.SIG AOC
support (ECMA-212) with the events passed to the upper layer.
Review: https://reviewboard.asterisk.org/r/538/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1737 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Added ability to send and receive ETSI ECT messages to eliminate tromboned
calls.
Added ETSI support to an existing API call to send ECT messages when the
upper level indicates to transfer specified calls.
The libpri API was extended to indicate to the upper layer that the far
end requests the transfer of the indicated calls.
Review: https://reviewboard.asterisk.org/r/521/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1723 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Call Completion Supplementary Service (CCSS) added for the following
switch types: ETSI PTMP, ETSI PTP, Q.SIG.
Specifications:
ETS 300 359 CCBS for PTMP and PTP
ETS 301 065 CCNR for PTMP and PTP
ECMA-186 Call Completion for Q.SIG
Several support services were added to support CC:
Dummy Call Reference.
Q.931 REGISTER message.
Dynamic expansion of the number of available timers (up to 8192).
Enhanced facility message handling.
Current implementation limitations preclude the following:
CC service retention is not supported.
Q.SIG path reservation is not supported.
(closes issue #14292)
Reported by: tomaso
Tested by: rmudgett
JIRA SWP-1493
Review: https://reviewboard.asterisk.org/r/522/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1714 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Revision -r1489 corrected a deviation from Q.931 Section 5.3.2. However,
this resulted in an unexpected behaviour change to the upper layer
(Asterisk).
This change restores the legacy hangup behaviour if the new API call is
not used. Use pri_hangup_fix_enable() to follow Q.931 Section 5.3.2 call
hangup better.
(closes issue #17104)
Reported by: shawkris
Tested by: rmudgett
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1688 2fbb986a-6c06-0410-b554-c9c1f0a7f128
1) No sent messages will remain in the APDU queue unless they have an
active timer to remove them. The dummy call reference call and global
call reference call structures will not act like a memory leak to sent
messages.
2) The new T-RESPONSE timer will be the generic response guard if the
standards do not otherwise specify a timer for a message response.
3) The callback will be called. If it is called because of a response
message, then the callback has an opportunity to indicate if more
responses are expected.
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1322 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Fixes problem where PTMP NT mode responds erroneously to a FACILITY
message from a phone on the dummy call reference. LibPRI behaved as if
the dummy call reference were an invalid call reference and proceeded to
respond on the global call reference.
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1275 2fbb986a-6c06-0410-b554-c9c1f0a7f128
* Added support for BRI PTMP NT mode. (Overlap dialing NT -> TE not supported.)
* Added handling of received HOLD/RETRIEVE messages and the optional ability
to transfer a held call on disconnect similar to an analog phone.
* Added CallRerouting/CallDeflection support for Q.SIG, ETSI PTP, ETSI PTMP.
Will reroute/deflect an outgoing call when receive the message.
Can use the DAHDISendCallreroutingFacility to send the message for the
supported switches.
* Added ability to send/receive keypad digits in the SETUP message.
Send keypad digits in SETUP message: Dial(DAHDI/g1[/K<keypad_digits>][/extension])
Access any received keypad digits in SETUP message by: ${CHANNEL(keypad_digits)}
(closes issue #15048)
Tested by: rmudgett, mattf
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1242 2fbb986a-6c06-0410-b554-c9c1f0a7f128
The Telecom Specs in NZ suggests that SUB ADDRESS is always on, so doing
"desk to desk" between offices each with an asterisk box over the ISDN
should then be possible, without a whole load of DDI numbers required.
(closes issue #15604)
Reported by: alecdavis
Patches:
libpri_subaddr_trunk.diff11.txt uploaded by alecdavis (license 585)
Some minor modificatons were made.
Tested by: alecdavis, rmudgett
Review: https://reviewboard.asterisk.org/r/406/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1230 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Also make sure that service maintenance messages have the channel id
parameters reinitialized for each message since they are sent over the
global call reference.
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1051 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Add Connected Line Presentation (COLP) support to chan_dahdi/libpri as an
addition to issue 8824. This is the libpri portion. COLP support is now
available for ETSI PTP, ETSI PTMP, and Q.SIG with this patch.
(closes issue #14068)
Tested by: rmudgett
Review: https://reviewboard.asterisk.org/r/339/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@982 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Add the ability to transmit a Reverse Charging Indication IE during a SETUP
message. In passing, re-work some of the receive logic to be forwards
compatible with new RCI values that may be added in the future. Also removed
the PRI_REVERSECHARGE_SUPPORT define that I added on the last commit since we
can just check for PRI_REVERSECHARGE_NONE or _REQUESTED on the Asterisk side to
determine support for this.
Special thanks to rmudgett who could have written this in half the time he spent
reviewing it, but instead talked me through it. Much appreciated!
(issue #13760)
Reported by: mrgabu
Review: https://reviewboard.asterisk.org/r/292/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@907 2fbb986a-6c06-0410-b554-c9c1f0a7f128
These API calls do not modify the string supplied, and should not be allowed to modify it, so this patch adds a 'const' qualifier to that argument to allow the compiler to enforce this restriction (and allow callers of the API that already have a 'const' pointer to be able to pass it to this API).
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@798 2fbb986a-6c06-0410-b554-c9c1f0a7f128
This adds support for two new message types: Service and Service Acknowledge.
When a channel receives a service message it will either take the channel in
or out of service and then send a service acknowledgment. Although not
enforced here (enforced in chan_dahdi), the service messages are only supported
with switch types 4ess/5ess. The required Asterisk changes will be coming next.
(issue #3450)
Reported by: cmaj
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@732 2fbb986a-6c06-0410-b554-c9c1f0a7f128
