Added support to the libpri API to control the inband audio available
progress indication ie on the SETUP_ACKNOWLEDGE message.
* Added the progress indication ie progressmask value to the struct
pri_event_setup_ack so the PRI_EVENT_SETUP_ACK event can indicate when a
SETUP_ACKNOWLEDGE comes in with inband audio (ie dialtone).
* Added pri_setup_ack() so when the SETUP_ACKNOWLEDGE message is sent it
can indicate if inband audio is present (ie dialtone).
This patch and a corresponding change in Asterisk work together to allow
Asterisk to control the inband audio available progress indication ie on
the SETUP_ACKNOWLEDGE message when dialtone is present.
AST-1338 #close
Reported by: Tyler Stewart
Review: https://reviewboard.asterisk.org/r/3520/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@2320 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Q.931 defines the T316 timer to retransmit RESTART messages if a RESTART
ACKNOWLEDGE message is not received before the timer expires. Q.931
defaults the time of T316 to 2 minutes with the default number of
consecutive RESTART failures as two.
* To support legacy behavior, the T316 timer is disabled by default. It
is also disabled because the user cannot configure it to disabled if it is
enabled.
* The N316 count is created to allow the number of RESTART attempts to be
configurable. Note you will need to recompile Asterisk to be able to
configure N316.
(issue ASTERISK-19608)
(issue AST-815)
(closes issue PRI-133)
Reported by: Mike Boylan
Tested by: rmudgett
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@2288 2fbb986a-6c06-0410-b554-c9c1f0a7f128
France Telecom brings layer 2 and layer 1 down on BRI lines when the line
is idle. When layer 1 goes down Asterisk cannot make outgoing calls and
the HA8 and HB8 cards also get IRQ misses.
The inability to make outgoing calls is because the line is in red alarm
and Asterisk will not make calls over a line it considers unavailable.
The IRQ misses for the HA8 and HB8 card are because the hardware is
switching clock sources from the line which just brought layer 1 down to
internal timing.
There is a DAHDI option for the B410P card to not tell Asterisk that layer
1 went down so Asterisk will allow outgoing calls: "modprobe wcb4xxp
teignored=1". There is a similar DAHDI option for the HA8 and HB8 cards:
"modprobe wctdm24xxp bri_teignored=1". Unfortunately that will not clear
up the IRQ misses when the telco brings layer 1 down.
* Add layer 2 persistence option to customize the layer 2 behavior on BRI
PTMP lines. The new option has three settings: 1) Use libpri default
layer 2 setting. 2) Keep layer 2 up. Bring layer 2 back up when the peer
brings it down. 3) Leave layer 2 down when the peer brings it down.
Layer 2 will be brought up as needed for outgoing calls.
(issue AST-598)
Reported by: Trey Blancher
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@2273 2fbb986a-6c06-0410-b554-c9c1f0a7f128
The NEC SV8300 rejects the Q931_IE_TIME_DATE for Q.SIG.
Add option to specify if and how much of the current time is put in
Q931_IE_TIME_DATE.
* Send date/time ie never.
* Send date/time ie date only.
* Send date/time ie date and hour.
* Send date/time ie date, hour, and minute.
* Send date/time ie date, hour, minute, and second.
* Send date/time ie default: Libpri will send date and hhmm only when in
NT PTMP mode to support ISDN phones.
(closes issue #19221)
Reported by: kenner
JIRA SWP-3396
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@2266 2fbb986a-6c06-0410-b554-c9c1f0a7f128
1) The "controlling user number" is always the number of the voice mail box
which is identical with the subscriber number itself. This number which
is listed in the ISDN phone MWI menu cannot be called back to contact the
voice mail box. The controlling user number should be made configurable.
2) The MWI indication is not restricted to a user (broadcast facility with
dummy call reference). A called party IE should be added to address only
the relevant MSN. (ETSI 300-196 Section 8.3.2.4)
JIRA ABE-2738
JIRA SWP-2846
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@2262 2fbb986a-6c06-0410-b554-c9c1f0a7f128
* Fixed stopping T303 too early on a NT PTMP broadcast SETUP call if a
subcall just receives a RELEASE_COMPLETE(busy).
* Fixed a valgrind reported invalid read/write when hanging up a NT PTMP
broadcast SETUP call.
JIRA LIBPRI-32
JIRA SWP-2548
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@2238 2fbb986a-6c06-0410-b554-c9c1f0a7f128
The display ie handling can be controlled independently in the send and
receive directions with the following options:
* Block display text data.
* Use display text in SETUP/CONNECT messages for name.
* Use display text for COLP name updates (FACILITY/NOTIFY as appropriate).
* Pass arbitrary display text during a call. Sent in INFORMATION
messages. Received from any message that the display text was not used as
a name.
If the display options are not set then the options default to legacy
behavior.
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@2190 2fbb986a-6c06-0410-b554-c9c1f0a7f128
There currently exists a pri_new_cb() API call that allows you to create a
PRI with user-defined I/O read and write callbacks, and option userdata.
Add the same capability for BRI interfaces by adding a pri_new_bri_cb()
API function.
(closes issue #16477)
Reported by: nic_bellamy
Patches:
pri_new_bri_cb_api.patch uploaded by nic bellamy (license 299) (with minor cosmetic changes)
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1836 2fbb986a-6c06-0410-b554-c9c1f0a7f128
This feature passes ETSI AOC-S, AOC-D, and AOC-E message information to
the upper layer (i.e. Asterisk) for processing.
Relevant specification: EN 300 182
Consideration was made for the possible future addition of Q.SIG AOC
support (ECMA-212) with the events passed to the upper layer.
Review: https://reviewboard.asterisk.org/r/538/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1737 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Added ability to send and receive ETSI ECT messages to eliminate tromboned
calls.
Added ETSI support to an existing API call to send ECT messages when the
upper level indicates to transfer specified calls.
The libpri API was extended to indicate to the upper layer that the far
end requests the transfer of the indicated calls.
Review: https://reviewboard.asterisk.org/r/521/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1723 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Call Completion Supplementary Service (CCSS) added for the following
switch types: ETSI PTMP, ETSI PTP, Q.SIG.
Specifications:
ETS 300 359 CCBS for PTMP and PTP
ETS 301 065 CCNR for PTMP and PTP
ECMA-186 Call Completion for Q.SIG
Several support services were added to support CC:
Dummy Call Reference.
Q.931 REGISTER message.
Dynamic expansion of the number of available timers (up to 8192).
Enhanced facility message handling.
Current implementation limitations preclude the following:
CC service retention is not supported.
Q.SIG path reservation is not supported.
(closes issue #14292)
Reported by: tomaso
Tested by: rmudgett
JIRA SWP-1493
Review: https://reviewboard.asterisk.org/r/522/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1714 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Revision -r1489 corrected a deviation from Q.931 Section 5.3.2. However,
this resulted in an unexpected behaviour change to the upper layer
(Asterisk).
This change restores the legacy hangup behaviour if the new API call is
not used. Use pri_hangup_fix_enable() to follow Q.931 Section 5.3.2 call
hangup better.
(closes issue #17104)
Reported by: shawkris
Tested by: rmudgett
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1688 2fbb986a-6c06-0410-b554-c9c1f0a7f128
1) No sent messages will remain in the APDU queue unless they have an
active timer to remove them. The dummy call reference call and global
call reference call structures will not act like a memory leak to sent
messages.
2) The new T-RESPONSE timer will be the generic response guard if the
standards do not otherwise specify a timer for a message response.
3) The callback will be called. If it is called because of a response
message, then the callback has an opportunity to indicate if more
responses are expected.
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1322 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Fixes problem where PTMP NT mode responds erroneously to a FACILITY
message from a phone on the dummy call reference. LibPRI behaved as if
the dummy call reference were an invalid call reference and proceeded to
respond on the global call reference.
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1275 2fbb986a-6c06-0410-b554-c9c1f0a7f128
* Added support for BRI PTMP NT mode. (Overlap dialing NT -> TE not supported.)
* Added handling of received HOLD/RETRIEVE messages and the optional ability
to transfer a held call on disconnect similar to an analog phone.
* Added CallRerouting/CallDeflection support for Q.SIG, ETSI PTP, ETSI PTMP.
Will reroute/deflect an outgoing call when receive the message.
Can use the DAHDISendCallreroutingFacility to send the message for the
supported switches.
* Added ability to send/receive keypad digits in the SETUP message.
Send keypad digits in SETUP message: Dial(DAHDI/g1[/K<keypad_digits>][/extension])
Access any received keypad digits in SETUP message by: ${CHANNEL(keypad_digits)}
(closes issue #15048)
Tested by: rmudgett, mattf
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1242 2fbb986a-6c06-0410-b554-c9c1f0a7f128
The Telecom Specs in NZ suggests that SUB ADDRESS is always on, so doing
"desk to desk" between offices each with an asterisk box over the ISDN
should then be possible, without a whole load of DDI numbers required.
(closes issue #15604)
Reported by: alecdavis
Patches:
libpri_subaddr_trunk.diff11.txt uploaded by alecdavis (license 585)
Some minor modificatons were made.
Tested by: alecdavis, rmudgett
Review: https://reviewboard.asterisk.org/r/406/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1230 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Also make sure that service maintenance messages have the channel id
parameters reinitialized for each message since they are sent over the
global call reference.
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@1051 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Add Connected Line Presentation (COLP) support to chan_dahdi/libpri as an
addition to issue 8824. This is the libpri portion. COLP support is now
available for ETSI PTP, ETSI PTMP, and Q.SIG with this patch.
(closes issue #14068)
Tested by: rmudgett
Review: https://reviewboard.asterisk.org/r/339/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@982 2fbb986a-6c06-0410-b554-c9c1f0a7f128
Add the ability to transmit a Reverse Charging Indication IE during a SETUP
message. In passing, re-work some of the receive logic to be forwards
compatible with new RCI values that may be added in the future. Also removed
the PRI_REVERSECHARGE_SUPPORT define that I added on the last commit since we
can just check for PRI_REVERSECHARGE_NONE or _REQUESTED on the Asterisk side to
determine support for this.
Special thanks to rmudgett who could have written this in half the time he spent
reviewing it, but instead talked me through it. Much appreciated!
(issue #13760)
Reported by: mrgabu
Review: https://reviewboard.asterisk.org/r/292/
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@907 2fbb986a-6c06-0410-b554-c9c1f0a7f128
These API calls do not modify the string supplied, and should not be allowed to modify it, so this patch adds a 'const' qualifier to that argument to allow the compiler to enforce this restriction (and allow callers of the API that already have a 'const' pointer to be able to pass it to this API).
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@798 2fbb986a-6c06-0410-b554-c9c1f0a7f128
This adds support for two new message types: Service and Service Acknowledge.
When a channel receives a service message it will either take the channel in
or out of service and then send a service acknowledgment. Although not
enforced here (enforced in chan_dahdi), the service messages are only supported
with switch types 4ess/5ess. The required Asterisk changes will be coming next.
(issue #3450)
Reported by: cmaj
git-svn-id: https://origsvn.digium.com/svn/libpri/branches/1.4@732 2fbb986a-6c06-0410-b554-c9c1f0a7f128
