569 lines
22 KiB
Plaintext
569 lines
22 KiB
Plaintext
|
|
; Inter-Asterisk eXchange driver definition
|
|
;
|
|
; This configuration is re-read at reload
|
|
; or with the CLI command
|
|
; reload chan_iax2.so
|
|
;
|
|
; General settings, like port number to bind to, and
|
|
; an option address (the default is to bind to all
|
|
; local addresses).
|
|
;
|
|
[general]
|
|
bindport=4569 ; bindport and bindaddr may be specified
|
|
; ; NOTE: bindport must be specified BEFORE
|
|
; bindaddr or may be specified on a specific
|
|
; bindaddr if followed by colon and port
|
|
; (e.g. bindaddr=192.168.0.1:4569)
|
|
;bindaddr=192.168.0.1 ; more than once to bind to multiple
|
|
; ; addresses, but the first will be the
|
|
; ; default
|
|
;
|
|
; Set iaxcompat to yes if you plan to use layered switches or
|
|
; some other scenario which may cause some delay when doing a
|
|
; lookup in the dialplan. It incurs a small performance hit to
|
|
; enable it. This option causes Asterisk to spawn a separate thread
|
|
; when it receives an IAX DPREQ (Dialplan Request) instead of
|
|
; blocking while it waits for a response.
|
|
;
|
|
;iaxcompat=yes
|
|
;
|
|
; Disable UDP checksums (if nochecksums is set, then no checkums will
|
|
; be calculated/checked on systems supporting this feature)
|
|
;
|
|
;nochecksums=no
|
|
;
|
|
;
|
|
; For increased security against brute force password attacks
|
|
; enable "delayreject" which will delay the sending of authentication
|
|
; reject for REGREQ or AUTHREP if there is a password.
|
|
;
|
|
;delayreject=yes
|
|
;
|
|
; You may specify a global default AMA flag for iaxtel calls. It must be
|
|
; one of 'default', 'omit', 'billing', or 'documentation'. These flags
|
|
; are used in the generation of call detail records.
|
|
;
|
|
;amaflags=default
|
|
;
|
|
; ADSI (Analog Display Services Interface) can be enabled if you have
|
|
; (or may have) ADSI compatible CPE equipment
|
|
;
|
|
;adsi=no
|
|
;
|
|
; Perform an SRV lookup on outbound calls
|
|
;
|
|
;srvlookup=yes
|
|
;
|
|
; You may specify a default account for Call Detail Records in addition
|
|
; to specifying on a per-user basis
|
|
;
|
|
;accountcode=lss0101
|
|
;
|
|
; You may specify a global default language for users.
|
|
; Can be specified also on a per-user basis
|
|
; If omitted, will fallback to english
|
|
;
|
|
;language=en
|
|
;
|
|
; This option specifies a preference for which music on hold class this channel
|
|
; should listen to when put on hold if the music class has not been set on the
|
|
; channel with Set(CHANNEL(musicclass)=whatever) in the dialplan, and the peer
|
|
; channel putting this one on hold did not suggest a music class.
|
|
;
|
|
; If this option is set to "passthrough", then the hold message will always be
|
|
; passed through as signalling instead of generating hold music locally.
|
|
;
|
|
; This option may be specified globally, or on a per-user or per-peer basis.
|
|
;
|
|
;mohinterpret=default
|
|
;
|
|
; This option specifies which music on hold class to suggest to the peer channel
|
|
; when this channel places the peer on hold. It may be specified globally or on
|
|
; a per-user or per-peer basis.
|
|
;
|
|
;mohsuggest=default
|
|
;
|
|
; Specify bandwidth of low, medium, or high to control which codecs are used
|
|
; in general.
|
|
;
|
|
bandwidth=low
|
|
;
|
|
; You can also fine tune codecs here using "allow" and "disallow" clauses
|
|
; with specific codecs. Use "all" to represent all formats.
|
|
;
|
|
;allow=all ; same as bandwidth=high
|
|
;disallow=g723.1 ; Hm... Proprietary, don't use it...
|
|
disallow=lpc10 ; Icky sound quality... Mr. Roboto.
|
|
;allow=gsm ; Always allow GSM, it's cool :)
|
|
;
|
|
|
|
; You can adjust several parameters relating to the jitter buffer.
|
|
; The jitter buffer's function is to compensate for varying
|
|
; network delay.
|
|
;
|
|
; All the jitter buffer settings are in milliseconds.
|
|
; The jitter buffer works for INCOMING audio - the outbound audio
|
|
; will be dejittered by the jitter buffer at the other end.
|
|
;
|
|
; jitterbuffer=yes|no: global default as to whether you want
|
|
; the jitter buffer at all.
|
|
;
|
|
; forcejitterbuffer=yes|no: in the ideal world, when we bridge VoIP channels
|
|
; we don't want to do jitterbuffering on the switch, since the endpoints
|
|
; can each handle this. However, some endpoints may have poor jitterbuffers
|
|
; themselves, so this option will force * to always jitterbuffer, even in this
|
|
; case.
|
|
;
|
|
; maxjitterbuffer: a maximum size for the jitter buffer.
|
|
; Setting a reasonable maximum here will prevent the call delay
|
|
; from rising to silly values in extreme situations; you'll hear
|
|
; SOMETHING, even though it will be jittery.
|
|
;
|
|
; resyncthreshold: when the jitterbuffer notices a significant change in delay
|
|
; that continues over a few frames, it will resync, assuming that the change in
|
|
; delay was caused by a timestamping mix-up. The threshold for noticing a
|
|
; change in delay is measured as twice the measured jitter plus this resync
|
|
; threshold.
|
|
; Resyncing can be disabled by setting this parameter to -1.
|
|
;
|
|
; maxjitterinterps: the maximum number of interpolation frames the jitterbuffer
|
|
; should return in a row. Since some clients do not send CNG/DTX frames to
|
|
; indicate silence, the jitterbuffer will assume silence has begun after
|
|
; returning this many interpolations. This prevents interpolating throughout
|
|
; a long silence.
|
|
;
|
|
;
|
|
; jittertargetextra: number of milliseconds by which the new jitter buffer
|
|
; will pad its size. the default is 40, so without modification, the new
|
|
; jitter buffer will set its size to the jitter value plus 40 milliseconds.
|
|
; increasing this value may help if your network normally has low jitter,
|
|
; but occasionally has spikes.
|
|
;
|
|
|
|
jitterbuffer=no
|
|
forcejitterbuffer=no
|
|
;maxjitterbuffer=1000
|
|
;maxjitterinterps=10
|
|
;resyncthreshold=1000
|
|
;jittertargetextra=40
|
|
|
|
; Minimum and maximum amounts of time that IAX peers can request as
|
|
; a registration expiration interval (in seconds).
|
|
; minregexpire = 60
|
|
; maxregexpire = 60
|
|
;
|
|
; Enable IAX2 encryption. The default is no.
|
|
;
|
|
; encryption = yes
|
|
;
|
|
; Force encryption insures no connection is established unless both sides support
|
|
; encryption. By turning this option on, encryption is automatically turned on as well.
|
|
;
|
|
; forceencryption = yes
|
|
|
|
; This option defines the maximum payload in bytes an IAX2 trunk can support at a given time.
|
|
; The best way to explain this is to provide an example. If the maximum number of calls
|
|
; to be supported is 800, and each call transmits 20ms frames of audio using ulaw
|
|
; ((8000hz / 1000ms) * 20ms * 1 byte per sample = 160 bytes per frame), the maximum load
|
|
; in bytes is (160 bytes per frame) * (800 calls) = 128000 bytes total. Once this limit is
|
|
; reached, calls may be dropped or begin to lose audio. Depending on the codec in use and
|
|
; number of channels to be supported this value may need to be raised, but in most cases the
|
|
; default value is large enough.
|
|
;
|
|
; trunkmaxsize = 128000 ; defaults to 128000 bytes, which supports up to 800 calls of ulaw
|
|
; ; at 20ms a frame.
|
|
|
|
; With a large amount of traffic on IAX2 trunks, there is a risk of bad voice quality when
|
|
; allowing the Linux system to handle fragmentation of UDP packets. Depending on the size of
|
|
; each payload, allowing the O/S to handle fragmentation may not be very efficient. This
|
|
; setting sets the maximum transmission unit for IAX2 UDP trunking. The default is 1240 bytes
|
|
; which means if a trunk's payload is over 1240 bytes for every 20ms it will be broken into
|
|
; multiple 1240 byte messages. Zero disables this functionality and let's the O/S handle
|
|
; fragmentation.
|
|
;
|
|
; trunkmtu = 1240 ; trunk data will be sent in 1240 byte messages.
|
|
|
|
; trunkfreq sets how frequently trunk messages are sent in milliseconds. This value is 20ms by
|
|
; default, which means the trunk will send all the date queued to it in the past 20ms. By
|
|
; increasing the time between sending trunk messages, the trunk's payload size will increase as
|
|
; well. Note, depending on the size set by trunkmtu, messages may be sent more often than
|
|
; specified. For example if a trunk's message size grows to the trunkmtu size before 20ms is
|
|
; reached that message will be sent immediately.
|
|
;
|
|
; trunkfreq=20 ; How frequently to send trunk msgs (in ms). This is 20ms by default.
|
|
|
|
; Should we send timestamps for the individual sub-frames within trunk frames?
|
|
; There is a small bandwidth use for these (less than 1kbps/call), but they
|
|
; ensure that frame timestamps get sent end-to-end properly. If both ends of
|
|
; all your trunks go directly to TDM, _and_ your trunkfreq equals the frame
|
|
; length for your codecs, you can probably suppress these. The receiver must
|
|
; also support this feature, although they do not also need to have it enabled.
|
|
;
|
|
; trunktimestamps=yes
|
|
;
|
|
|
|
; IAX helper threads
|
|
|
|
; Establishes the number of iax helper threads to handle I/O.
|
|
; iaxthreadcount = 10
|
|
; Establishes the number of extra dynamic threads that may be spawned to handle I/O
|
|
; iaxmaxthreadcount = 100
|
|
;
|
|
; We can register with another IAX server to let him know where we are
|
|
; in case we have a dynamic IP address for example
|
|
;
|
|
; Register with tormenta using username marko and password secretpass
|
|
;
|
|
;register => marko:secretpass@tormenta.linux-support.net
|
|
;
|
|
; Register joe at remote host with no password
|
|
;
|
|
;register => joe@remotehost:5656
|
|
;
|
|
; Register marko at tormenta.linux-support.net using RSA key "torkey"
|
|
;
|
|
;register => marko:[torkey]@tormenta.linux-support.net
|
|
;
|
|
; Sample Registration for iaxtel
|
|
;
|
|
; Visit http://www.iaxtel.com to register with iaxtel. Replace "user"
|
|
; and "pass" with your username and password for iaxtel. Incoming
|
|
; calls arrive at the "s" extension of "default" context.
|
|
;
|
|
;register => user:pass@iaxtel.com
|
|
;
|
|
; Sample Registration for IAX + FWD
|
|
;
|
|
; To register using IAX with FWD, it must be enabled by visiting the URL
|
|
; http://www.fwdnet.net/index.php?section_id=112
|
|
;
|
|
; Note that you need an extension in you default context which matches
|
|
; your free world dialup number. Please replace "FWDNumber" with your
|
|
; FWD number and "passwd" with your password.
|
|
;
|
|
;register => FWDNumber:passwd@iax.fwdnet.net
|
|
;
|
|
;
|
|
; You can disable authentication debugging to reduce the amount of
|
|
; debugging traffic.
|
|
;
|
|
authdebug=yes
|
|
;
|
|
; See qos.tex or Quality of Service section of asterisk.pdf for a description of these parameters.
|
|
;tos=ef
|
|
;cos=5
|
|
;
|
|
; If regcontext is specified, Asterisk will dynamically create and destroy
|
|
; a NoOp priority 1 extension for a given peer who registers or unregisters
|
|
; with us. The actual extension is the 'regexten' parameter of the registering
|
|
; peer or its name if 'regexten' is not provided. More than one regexten
|
|
; may be supplied if they are separated by '&'. Patterns may be used in
|
|
; regexten.
|
|
;
|
|
;regcontext=iaxregistrations
|
|
;
|
|
; If we don't get ACK to our NEW within 2000ms, and autokill is set to yes,
|
|
; then we cancel the whole thing (that's enough time for one retransmission
|
|
; only). This is used to keep things from stalling for a long time for a host
|
|
; that is not available, but would be ill advised for bad connections. In
|
|
; addition to 'yes' or 'no' you can also specify a number of milliseconds.
|
|
; See 'qualify' for individual peers to turn on for just a specific peer.
|
|
;
|
|
autokill=yes
|
|
;
|
|
; codecpriority controls the codec negotiation of an inbound IAX call.
|
|
; This option is inherited to all user entities. It can also be defined
|
|
; in each user entity separately which will override the setting in general.
|
|
;
|
|
; The valid values are:
|
|
;
|
|
; caller - Consider the callers preferred order ahead of the host's.
|
|
; host - Consider the host's preferred order ahead of the caller's.
|
|
; disabled - Disable the consideration of codec preference altogether.
|
|
; (this is the original behaviour before preferences were added)
|
|
; reqonly - Same as disabled, only do not consider capabilities if
|
|
; the requested format is not available the call will only
|
|
; be accepted if the requested format is available.
|
|
;
|
|
; The default value is 'host'
|
|
;
|
|
;codecpriority=host
|
|
;
|
|
; allowfwdownload controls whether this host will serve out firmware to
|
|
; IAX clients which request it. This has only been used for the IAXy,
|
|
; and it has been recently proven that this firmware distribution method
|
|
; can be used as a source of traffic amplification attacks. Also, the
|
|
; IAXy firmware has not been updated for at least 18 months, so unless
|
|
; you are provisioning IAXys in a secure network, we recommend that you
|
|
; leave this option to the default, off.
|
|
;
|
|
;allowfwdownload=yes
|
|
|
|
;rtcachefriends=yes ; Cache realtime friends by adding them to the internal list
|
|
; just like friends added from the config file only on a
|
|
; as-needed basis? (yes|no)
|
|
|
|
;rtupdate=yes ; Send registry updates to database using realtime? (yes|no)
|
|
; If set to yes, when a IAX2 peer registers successfully,
|
|
; the ip address, the origination port, the registration period,
|
|
; and the username of the peer will be set to database via realtime.
|
|
; If not present, defaults to 'yes'.
|
|
|
|
;rtautoclear=yes ; Auto-Expire friends created on the fly on the same schedule
|
|
; as if it had just registered? (yes|no|<seconds>)
|
|
; If set to yes, when the registration expires, the friend will
|
|
; vanish from the configuration until requested again.
|
|
; If set to an integer, friends expire within this number of
|
|
; seconds instead of the registration interval.
|
|
|
|
;rtignoreregexpire=yes ; When reading a peer from Realtime, if the peer's registration
|
|
; has expired based on its registration interval, used the stored
|
|
; address information regardless. (yes|no)
|
|
|
|
;parkinglot=edvina ; Default parkinglot for IAX peers and users
|
|
; This can also be configured per device
|
|
; Parkinglots are defined in features.conf
|
|
|
|
;
|
|
; The following two options are used to disable call token validation for the
|
|
; purposes of interoperability with IAX2 endpoints that do not yet support it.
|
|
;
|
|
; Call token validation can be set as optional for a single IP address or IP
|
|
; address range by using the 'calltokenoptional' option. 'calltokenoptional' is
|
|
; only a global option.
|
|
;
|
|
;calltokenoptional=209.16.236.73/255.255.255.0
|
|
calltokenoptional=0.0.0.0/0.0.0.0
|
|
;
|
|
; By setting 'requirecalltoken=no', call token validation becomes optional for
|
|
; that peer/user. By setting 'requirecalltoken=auto', call token validation
|
|
; is optional until a call token supporting peer registers successfully using
|
|
; call token validation. This is used as an indication that from now on, we
|
|
; can require it from this peer. So, requirecalltoken is internally set to yes.
|
|
; requirecalltoken may only be used in peer/user/friend definitions,
|
|
; not in the global scope.
|
|
; By default, 'requirecalltoken=yes'.
|
|
;
|
|
;requirecalltoken=no
|
|
;
|
|
|
|
;
|
|
; These options are used to limit the amount of call numbers allocated to a
|
|
; single IP address. Before changing any of these values, it is highly encouraged
|
|
; to read the user guide associated with these options first. In most cases, the
|
|
; default values for these options are sufficient.
|
|
;
|
|
; The 'maxcallnumbers' option limits the amount of call numbers allowed for each
|
|
; individual remote IP address. Once an IP address reaches it's call number
|
|
; limit, no more new connections are allowed until the previous ones close. This
|
|
; option can be used in a peer definition as well, but only takes effect for
|
|
; the IP of a dynamic peer after it completes registration.
|
|
;
|
|
;maxcallnumbers=512
|
|
;
|
|
; The 'maxcallnumbers_nonvalidated' is used to set the combined number of call
|
|
; numbers that can be allocated for connections where call token validation
|
|
; has been disabled. Unlike the 'maxcallnumbers' option, this limit is not
|
|
; separate for each individual IP address. Any connection resulting in a
|
|
; non-call token validated call number being allocated contributes to this
|
|
; limit. For use cases, see the call token user guide. This option's
|
|
; default value of 8192 should be sufficient in most cases.
|
|
;
|
|
;maxcallnumbers_nonvalidated=1024
|
|
;
|
|
; The [callnumberlimits] section allows custom call number limits to be set
|
|
; for specific IP addresses and IP address ranges. These limits take precedence
|
|
; over the global 'maxcallnumbers' option, but may still be overridden by a
|
|
; peer defined 'maxcallnumbers' entry. Note that these limits take effect
|
|
; for every individual address within the range, not the range as a whole.
|
|
;
|
|
;[callnumberlimits]
|
|
;10.1.1.0/255.255.255.0 = 24
|
|
;10.1.2.0/255.255.255.0 = 32
|
|
;
|
|
|
|
; The shrinkcallerid function removes '(', ' ', ')', non-trailing '.', and '-' not
|
|
; in square brackets. For example, the caller id value 555.5555 becomes 5555555
|
|
; when this option is enabled. Disabling this option results in no modification
|
|
; of the caller id value, which is necessary when the caller id represents something
|
|
; that must be preserved. This option can only be used in the [general] section.
|
|
; By default this option is on.
|
|
;
|
|
;shrinkcallerid=yes ; on by default
|
|
|
|
; Guest sections for unauthenticated connection attempts. Just specify an
|
|
; empty secret, or provide no secret section.
|
|
;
|
|
[guest]
|
|
type=user
|
|
context=fgcom
|
|
callerid="Guest IAX User"
|
|
|
|
requirecalltoken=no
|
|
|
|
;
|
|
; Trust Caller*ID Coming from iaxtel.com
|
|
;
|
|
[iaxtel]
|
|
type=user
|
|
context=default
|
|
auth=rsa
|
|
inkeys=iaxtel
|
|
|
|
;
|
|
; Trust Caller*ID Coming from iax.fwdnet.net
|
|
;
|
|
[iaxfwd]
|
|
type=user
|
|
context=default
|
|
auth=rsa
|
|
inkeys=freeworlddialup
|
|
|
|
;
|
|
; Trust callerid delivered over DUNDi/e164
|
|
;
|
|
;
|
|
;[dundi]
|
|
;type=user
|
|
;dbsecret=dundi/secret
|
|
;context=dundi-e164-local
|
|
|
|
;
|
|
; Further user sections may be added, specifying a context and a secret used
|
|
; for connections with that given authentication name. Limited IP based
|
|
; access control is allowed by use of "permit" and "deny" keywords. Multiple
|
|
; rules are permitted. Multiple permitted contexts may be specified, in
|
|
; which case the first will be the default. You can also override caller*ID
|
|
; so that when you receive a call you set the Caller*ID to be what you want
|
|
; instead of trusting what the remote user provides
|
|
;
|
|
; There are three authentication methods that are supported: md5, plaintext,
|
|
; and rsa. The least secure is "plaintext", which sends passwords cleartext
|
|
; across the net. "md5" uses a challenge/response md5 sum arrangement, but
|
|
; still requires both ends have plain text access to the secret. "rsa" allows
|
|
; unidirectional secret knowledge through public/private keys. If "rsa"
|
|
; authentication is used, "inkeys" is a list of acceptable public keys on the
|
|
; local system that can be used to authenticate the remote peer, separated by
|
|
; the ":" character. "outkey" is a single, private key to use to authenticate
|
|
; to the other side. Public keys are named /var/lib/asterisk/keys/<name>.pub
|
|
; while private keys are named /var/lib/asterisk/keys/<name>.key. Private
|
|
; keys should always be 3DES encrypted.
|
|
;
|
|
;
|
|
; NOTE: All hostnames and IP addresses in this file are for example purposes
|
|
; only; you should not expect any of them to actually be available for
|
|
; your use.
|
|
;
|
|
;
|
|
;[markster]
|
|
;type=user
|
|
;context=default
|
|
;context=local
|
|
;auth=md5,plaintext,rsa
|
|
;secret=markpasswd
|
|
;setvar=ATTENDED_TRANSFER_COMPLETE_SOUND=beep ; This channel variable will
|
|
; cause the given audio file to
|
|
; be played upon completion of
|
|
; an attended transfer.
|
|
;dbsecret=mysecrets/place ; Secrets can be stored in astdb, too
|
|
;transfer=no ; Disable IAX native transfer
|
|
;transfer=mediaonly ; When doing IAX native transfers, transfer
|
|
; only media stream
|
|
;jitterbuffer=yes ; Override global setting an enable jitter buffer
|
|
; ; for this user
|
|
;maxauthreq=10 ; Set maximum number of outstanding AUTHREQs waiting for replies. Any further authentication attempts will be blocked
|
|
; ; if this limit is reached until they expire or a reply is received.
|
|
;callerid="Mark Spencer" <(256) 428-6275>
|
|
;deny=0.0.0.0/0.0.0.0
|
|
;accountcode=markster0101
|
|
;permit=209.16.236.73/255.255.255.0
|
|
;language=en ; Use english as default language
|
|
;encryption=yes ; Enable IAX2 encryption. The default is no.
|
|
;keyrotate=off ; This is a compatibility option for older versions of
|
|
; ; IAX2 that do not support key rotation with encryption.
|
|
; ; This option will disable the IAX_COMMAND_RTENC message.
|
|
; ; default is on.
|
|
; ;
|
|
;
|
|
; Peers may also be specified, with a secret and
|
|
; a remote hostname.
|
|
;
|
|
[demo]
|
|
type=peer
|
|
username=asterisk
|
|
secret=supersecret
|
|
host=216.207.245.47
|
|
;sendani=no
|
|
;host=asterisk.linux-support.net
|
|
;port=5036
|
|
;mask=255.255.255.255
|
|
;qualify=yes ; Make sure this peer is alive
|
|
;qualifysmoothing = yes ; use an average of the last two PONG
|
|
; results to reduce falsely detected LAGGED hosts
|
|
; Default: Off
|
|
;qualifyfreqok = 60000 ; how frequently to ping the peer when
|
|
; everything seems to be ok, in milliseconds
|
|
;qualifyfreqnotok = 10000 ; how frequently to ping the peer when it's
|
|
; either LAGGED or UNAVAILABLE, in milliseconds
|
|
;jitterbuffer=no ; Turn off jitter buffer for this peer
|
|
;
|
|
;encryption=yes ; Enable IAX2 encryption. The default is no.
|
|
;keyrotate=off ; This is a compatibility option for older versions of
|
|
; ; IAX2 that do not support key rotation with encryption.
|
|
; ; This option will disable the IAX_COMMAND_RTENC message.
|
|
; ; default is on.
|
|
; ;
|
|
; Peers can remotely register as well, so that they can be mobile. Default
|
|
; IP's can also optionally be given but are not required. Caller*ID can be
|
|
; suggested to the other side as well if it is for example a phone instead of
|
|
; another PBX.
|
|
;
|
|
|
|
;[dynamichost]
|
|
;host=dynamic
|
|
;secret=mysecret
|
|
;mailbox=1234 ; Notify about mailbox 1234
|
|
;inkeys=key1:key2
|
|
;peercontext=local ; Default context to request for calls to peer
|
|
;defaultip=216.207.245.34
|
|
;callerid="Some Host" <(256) 428-6011>
|
|
;
|
|
|
|
;
|
|
;[biggateway]
|
|
;type=peer
|
|
;host=192.168.0.1
|
|
;context=*
|
|
;secret=myscret
|
|
;trunk=yes ; Use IAX2 trunking with this host
|
|
;timezone=America/New_York ; Set a timezone for the date/time IE
|
|
;
|
|
|
|
;
|
|
; Friends are a short cut for creating a user and
|
|
; a peer with the same values.
|
|
;
|
|
;[marko]
|
|
;type=friend
|
|
;host=dynamic
|
|
;regexten=1234
|
|
;secret=moofoo ; Multiple secrets may be specified. For a "user", all
|
|
;secret=foomoo ; specified entries will be accepted as valid. For a "peer",
|
|
;secret=shazbot ; only the last specified secret will be used.
|
|
;context=default
|
|
;permit=0.0.0.0/0.0.0.0
|
|
|
|
;
|
|
; With immediate=yes, an IAX phone or a phone on an IAXy acts as a hot-line
|
|
; which goes immediately to the s extension when picked up. Useful for
|
|
; elevator phones, manual service, or other similar applications.
|
|
;
|
|
;[manual]
|
|
;type=friend
|
|
;host=dynamic
|
|
;immediate=yes ; go immediately to s extension when picked up
|
|
;secret=moofoo ; when immediate=yes is specified, secret is required
|
|
;context=number-please ; we start at the s extension in this context
|
|
;
|