971a45a807
* Extrainfo field contains junk data
* Caused by:
- The field is initialized to 0xFF values
- There was no null termination (and no room to add it)
* New code:
- Ensure that show_extrainfo() have null termination even if EEPROM
field is full.
- Replace trailing 0xFF characters with '\0' when reading this field
- Since our default burned EEPROM contain Extrainfo field full of
0xFF characters, this would make them look as null filled.
Internal Issue-Id: #1341
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.astersk.org/svn/dahdi/tools/trunk@10491 17933a7a-c749-41c5-a318-cba88f637d49
114 lines
3.6 KiB
C
114 lines
3.6 KiB
C
#ifndef MPPTALK_DEFS_H
|
|
#define MPPTALK_DEFS_H
|
|
/*
|
|
* Written by Oron Peled <oron@actcom.co.il>
|
|
* Copyright (C) 2008,2009,2010 Xorcom
|
|
*
|
|
* All rights reserved.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software
|
|
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*
|
|
*/
|
|
|
|
#include <xtalk_defs.h>
|
|
/*
|
|
* MPP - Managment Processor Protocol definitions
|
|
*/
|
|
|
|
/*
|
|
* OP Codes:
|
|
* MSB of op signifies a reply from device
|
|
*/
|
|
#define MPP_RENUM 0x0B /* Trigger USB renumeration */
|
|
#define MPP_EEPROM_SET 0x0D
|
|
|
|
/* AB capabilities */
|
|
#define MPP_CAPS_GET 0x0E
|
|
#define MPP_CAPS_GET_REPLY 0x8E
|
|
#define MPP_CAPS_SET 0x0F
|
|
|
|
#define MPP_DEV_SEND_START 0x05
|
|
#define MPP_DEV_SEND_SEG 0x07
|
|
#define MPP_DEV_SEND_END 0x09
|
|
|
|
/* Astribank Status */
|
|
#define MPP_STATUS_GET 0x11
|
|
#define MPP_STATUS_GET_REPLY 0x91
|
|
#define MPP_STATUS_GET_REPLY_V13 0x91 /* backward compat */
|
|
|
|
/* Get extra vendor information */
|
|
#define MPP_EXTRAINFO_GET 0x13
|
|
#define MPP_EXTRAINFO_GET_REPLY 0x93
|
|
#define MPP_EXTRAINFO_SET 0x15 /* Set extra vendor information */
|
|
|
|
#define MPP_EEPROM_BLK_RD 0x27
|
|
#define MPP_EEPROM_BLK_RD_REPLY 0xA7
|
|
|
|
#define MPP_SER_SEND 0x37
|
|
#define MPP_SER_RECV 0xB7
|
|
|
|
#define MPP_RESET 0x45 /* Reset both FPGA and USB firmwares */
|
|
#define MPP_HALF_RESET 0x47 /* Reset only FPGA firmware */
|
|
|
|
/* Twinstar */
|
|
#define MPP_TWS_WD_MODE_SET 0x31 /* Set watchdog off/on guard */
|
|
#define MPP_TWS_WD_MODE_GET 0x32 /* Current watchdog mode */
|
|
#define MPP_TWS_WD_MODE_GET_REPLY 0xB2 /* Current watchdog mode */
|
|
#define MPP_TWS_PORT_SET 0x34 /* USB-[0/1] */
|
|
#define MPP_TWS_PORT_GET 0x35 /* USB-[0/1] */
|
|
#define MPP_TWS_PORT_GET_REPLY 0xB5 /* USB-[0/1] */
|
|
#define MPP_TWS_PWR_GET 0x36 /* Power: bits -> USB ports */
|
|
#define MPP_TWS_PWR_GET_REPLY 0xB6 /* Power: bits -> USB ports */
|
|
|
|
/*
|
|
* Statuses
|
|
*/
|
|
#define STAT_OK 0x00 /* acknowledges previous command */
|
|
#define STAT_FAIL 0x01 /* Last command failed */
|
|
#define STAT_RESET_FAIL 0x02 /* reset failed */
|
|
#define STAT_NODEST 0x03 /* No destination is selected */
|
|
#define STAT_MISMATCH 0x04 /* Data mismatch */
|
|
#define STAT_NOACCESS 0x05 /* No access */
|
|
#define STAT_BAD_CMD 0x06 /* Bad command */
|
|
#define STAT_TOO_SHORT 0x07 /* Packet is too short */
|
|
#define STAT_ERROFFS 0x08 /* Offset error */
|
|
#define STAT_NOCODE 0x09 /* Source was not burned before */
|
|
#define STAT_NO_LEEPROM 0x0A /* Large EEPROM was not found */
|
|
#define STAT_NO_EEPROM 0x0B /* No EEPROM was found */
|
|
#define STAT_WRITE_FAIL 0x0C /* Writing to device failed */
|
|
#define STAT_FPGA_ERR 0x0D /* FPGA error */
|
|
#define STAT_KEY_ERR 0x0E /* Bad Capabilities Key */
|
|
#define STAT_NOCAPS_ERR 0x0F /* No matching capability */
|
|
#define STAT_NOPWR_ERR 0x10 /* No power on USB connector */
|
|
#define STAT_CAPS_FPGA_ERR 0x11 /* Setting of the capabilities while FPGA is loaded */
|
|
|
|
/* EEPROM_QUERY: i2cs(ID1, ID0) */
|
|
enum eeprom_type {
|
|
EEPROM_TYPE_NONE = 0,
|
|
EEPROM_TYPE_SMALL = 1,
|
|
EEPROM_TYPE_LARGE = 2,
|
|
EEPROM_TYPE_UNUSED = 3,
|
|
};
|
|
|
|
enum dev_dest {
|
|
DEST_NONE = 0x00,
|
|
DEST_FPGA = 0x01,
|
|
DEST_EEPROM = 0x02,
|
|
};
|
|
|
|
#define EXTRAINFO_SIZE 24
|
|
|
|
#endif /* MPPTALK_DEFS_H */
|