466357f5c2
This revision of DAHDI-Tools is the base revision for the switch to git. git-svn-id: http://svn.astersk.org/svn/dahdi/tools/tools/trunk@9159
170 lines
6.0 KiB
Plaintext
170 lines
6.0 KiB
Plaintext
#
|
|
# /etc/dahdi/genconf_parameters
|
|
#
|
|
# This file contains parameters that affect the
|
|
# dahdi_genconf configuration generator.
|
|
#
|
|
# Syntax:
|
|
# * A comment from '#' to end of line
|
|
# * Blank lines ignored
|
|
# * Whitespace at end of line trimmed
|
|
# * Single valued items:
|
|
# key <whitespace...> value
|
|
# * List valued items:
|
|
# key
|
|
# <whitespace...>value1
|
|
# <whitespace...>value2
|
|
# ...
|
|
#
|
|
|
|
# When generating extensions for chan_dahdi.conf or users.conf etc: the
|
|
# extension number will be channel_number+base_exten . The default is:
|
|
#base_exten 4000
|
|
#
|
|
# Make FXS (analog phones) extensions answer immediately (sets
|
|
# 'immediate = yes' for them in chan_dahdi.conf). Don't enable this before
|
|
# you're read documentation about this option.
|
|
#fxs_immediate yes
|
|
#
|
|
# For FXS (analog phones) - use KS or LS? ks is the only method for
|
|
# Asterisk to provide disconnect supervision and thus it would normally
|
|
# be preferred and is the default.
|
|
#fxs_default_start ls
|
|
#
|
|
# For FXO (analog lines) - use KS or LS? KS is the default and is
|
|
# normally the better choice as it allows detecting hang-ups on many
|
|
# lines.
|
|
#fxo_default_start ls
|
|
|
|
# Set tone zone values. This is used for playing tones (busy, dial-tone
|
|
# and such). The default is 'us'. This sets the value for both loadzone
|
|
# and defaultzone in system.conf .
|
|
#lc_country il
|
|
|
|
# The dialplan context into which to send trunks in chan_dahdi.conf or
|
|
# users.conf. The default value is:
|
|
#context_lines from-pstn
|
|
#
|
|
# The dialplan context into which to send extensions in chan_dahdi.conf or
|
|
# users.conf. The default value is:
|
|
#context_phones from-internal
|
|
#
|
|
# Two extra contexts for the input ports and output ports of an
|
|
# Astribank. Default values are:
|
|
#context_input astbank-input
|
|
#context_output astbank-output
|
|
|
|
# A group to put all analog phones in. By default 0, so you can dial to
|
|
# the 'first phone available' using Dahdi/g5 .
|
|
#group_phones 5
|
|
#
|
|
# A group in which to put all the channels belonging to some trunk.
|
|
# Thus you can dial through "some trunk" using Dahdi/G0/NUMBER
|
|
#group_lines 0
|
|
|
|
# Channels of digital trunk of span N are also added to group 10+N (that
|
|
# is: 14 for channels of span 4).
|
|
|
|
# Do we want to use PtP ('bri') or PtMP ('bri_ptmp') for BRI? PtMP
|
|
# allows connecting several CPE devices on the same network device
|
|
# (several BRI phones on the same line, kind of like several analog
|
|
# phones on the same analog line). However it is generally brings
|
|
# unnecessary complexity for a pbx-pbx connection. It is still the
|
|
# default as this is normally what you get for a BRI PSTN connection.
|
|
#bri_sig_style bri
|
|
#
|
|
# If this option is set (that is: not remmed-out), BRI NT ports will
|
|
# also be set as overlap. This is useful if you want to connect ISDN
|
|
# phones.
|
|
#brint_overlap
|
|
|
|
# The echo canceler to use. If you have a hardware echo canceler, just
|
|
# leave it be, as this one won't be used anyway.
|
|
#
|
|
# The default is mg2, but it may change in the future. E.g: a packager
|
|
# that bundles a better echo canceler may set it as the default, or
|
|
# dahdi_genconf will scan for the "best" echo canceler.
|
|
#
|
|
#echo_can hpec
|
|
#echo_can oslec
|
|
#echo_can none # to avoid echo canceler altogether
|
|
|
|
# bri_hardhdlc:
|
|
# 'yes' - forces BRI cards to use 'hardhdlc' signalling.
|
|
# 'no' - forces BRI cards to use 'dchan' (an alias for 'fcshdlc').
|
|
# It is usefull only for dahdi with the bristuff patch.
|
|
#
|
|
# If it is left out or set to 'auto':
|
|
# * Information supplied by the driver is used to decide:
|
|
# - Currently implemented for Astribanks.
|
|
# - Taken from /sys/bus/xpds/drivers/bri/dchan_hardhdlc.
|
|
# * Without this info, falls back to 'hardhdlc'.
|
|
#bri_hardhdlc auto
|
|
|
|
# For MFC/R2 Support: 'R2' will make E1 spans CAS and with the
|
|
# 'r2_idle_bits' bit in system.conf . It will also make dahdi_genconf default
|
|
# to generating the channels of this card in unicall.conf rather than in
|
|
# chan_dahdi.conf . The meaning of this may be extended somehow to support
|
|
# R2 through openr2/chan_dahdi later on.
|
|
#pri_connection_type R2
|
|
#pri_connection_type CAS
|
|
#
|
|
# Explicitly set the idle bits for E1 CAS (Sample value is the default):
|
|
#r2_idle_bits 1101
|
|
#
|
|
# Set T1 framing type to d4 instead of esf:
|
|
#tdm_framing d4
|
|
#
|
|
# Use E&M on CAS (default is FXS/FXO). If set, E1 spans will be used as
|
|
# E&M-E1 and T1 will use the requested type:
|
|
#em_signalling em
|
|
#em_signalling em_w
|
|
#em_signalling featd
|
|
#em_signalling featdtmf
|
|
#em_signalling featdtmf_ta
|
|
#em_signalling featb
|
|
#em_signalling fgccama
|
|
#em_signalling fgccamamf
|
|
#
|
|
# pri_termtype contains a list of settings:
|
|
# Currently the only setting is for TE or NT (the default is TE). This
|
|
# sets two different but normally related configuration items:
|
|
#
|
|
# A TE span will have *_cpe signalling in Asterisk and will also get
|
|
# timing from the remote party.
|
|
#
|
|
# A NT span will have *_new signalling in Asterisk and will provide
|
|
# timing to the remote party.
|
|
#
|
|
# pri_termtype is a list if span specs and configuration (TE/NT) for
|
|
# them. The first spec that matches is used. The matching is of perl
|
|
# regular expressions, but with '*' and '?' have their meaning from
|
|
# basic regular expressions.
|
|
#pri_termtype
|
|
# SPAN/2 NT
|
|
# SPAN/4 NT
|
|
#
|
|
#pri_termtype
|
|
# SPAN/* NT
|
|
#
|
|
# Astribanks can be matched by span and also by their:
|
|
# LABEL + XPD number:
|
|
# this is burned into the Astribank and won't change
|
|
# if it's connected via different USB port/hub
|
|
# CONNECTOR + XPD number:
|
|
# The USB path to which the Astribank is connected.
|
|
# Replacing an Astribank and connecting to the same USB port/hub
|
|
# would not change this property. However, any change in USB
|
|
# wiring (e.g: adding another hub) may alter this.
|
|
# NUM (XBUS number) + XPD number:
|
|
# The XBUS number. This is not stable and may even change
|
|
# between boots.
|
|
#
|
|
#pri_termtype
|
|
# LABEL/usb:INT01216/XPD-0[123] NT
|
|
# LABEL/usb:INT00375/XPD-0[123] NT
|
|
# CONNECTOR/@usb-0000:00:1d.7-1/XPD-0[123] NT
|
|
# CONNECTOR/@usb-0000:00:1d.7-2/XPD-0[123] NT
|
|
# NUM/XBUS-01/XPD-0[123] NT
|
|
# NUM/XBUS-03/XPD-0[123] NT
|