Make sure you have etc/asterisk in the live tree before generating
configuration.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10028 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This adds module parameter 'ring_trapez'. When set, the wave form of
the ring tone is set to be a trapezoid, rather than sine. Thus making
the ring stronger.
This is a boolean parameter of the module xpd_fxs. Takes effect at the
beginning of the next ring.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10022 a0bf4364-ded3-4de4-8d8a-66a801d63aff
gcc 4.6 complains about variables that are assigned values but then
never used.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10020 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In some cases the hardware echo canceller cannot be used. Mostly related to
an FXO module.
* FXO module if the first module is BRI or PRI
* FXS module if the Astribank has another FXO, no PRI/BRI, and is a sync
slave.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10019 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r9943 enabled the presence of hardware EC to be probed on a card. That
change did not account for wcb4xxp based cards that did not have a
hardware echocan on board.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10017 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The dual and quad span cards have a rotary switch onboard which controls
the order that cards serviced by this driver are registered with the
core of DAHDI. This commit adds a module parameter 'ignore_rotary'
which, when set to 1, causes the driver to ignore the position of the
rotary switch and only consider the physical slot when registering with
DAHDI.
Ignoring the rotary switch settings also permits the PCI device to be
bound and unbound from the driver at runtime since registration with
DAHDI no longer only happens when the module is first initialized.
By default, the rotary switch will still be used to determine
registration order. This commit does not change the default behavior.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10016 a0bf4364-ded3-4de4-8d8a-66a801d63aff
New Astribank II FPGA firmware and USB firmwares that add support for the
hardware echo canceller module.
Note that due to a bug in previous FPGA firmwares, an Astribank with such
older firmware and with a hardware echo canceller module will not have any
functioning audio at all.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10013 a0bf4364-ded3-4de4-8d8a-66a801d63aff
I failed to compile the commit exactly as it was committed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10008 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When true / 1 the FXO port will use a shorter off-hook calibration
delay. This is sometimes necessary in order to properly decode Type-II
Caller ID information which is sent shortly after an FXO port goes off
hook.
Defaults to 0 unless opermode is "JAPAN" then it will default to 1. This
functionality was ported from the wctdm.c driver.
DAHDI-854.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10006 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If an FXS port is configured to use kewl start signalling, when the FXS port
is "hungup" it should drop battery for 500ms so that any attached devices can
detect that the remote side has disconnected. The wctdm24xxp driver
since version 2.4.0 was only dropping battery for ~5-10 ms because it would
set "open" on the line, but then the next time it read the line feed register
state, it was setting the LINE feed register to the idle state.
This change checks if the line is forced open before setting the FXS port back
"onhook" so as to not turn on battery prematurely.
This fixes a regression introduced in r9070 "wctdm24xxp: Prevent FXS Proslic
staying in "Forward/Reverse OnHookTransfer...". DAHDI-849.
Checking for open on the line feed registered was originally suggested by Alec
Davis.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10002 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reverts commit r9879. Asterisk commit r264249 [1], which was committed
after the switch to enumerations, requires the maintenance modes to be
Changing the test in configure.ac from:
AST_C_DEFINE_CHECK([DAHDI], [DAHDI_RESET_COUNTERS], [dahdi/user.h], [230])
to:
AST_C_COMPILE_CHECK([DAHDI], [int foo = DAHDI_RESET_COUNTERS], [dahdi/user.h])
Would allow the maintenance modes to stand as enumerations but the potential
for users to run incompatible versions does not seem worth it at this point.
[1] http://svnview.digium.com/svn/asterisk?view=revision&revision=264249
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10000 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The firmware load has been moved into a workqueue to prevent the module load
from blocking for the duration of the firmware upload. This could be up to 40
seconds. Driver prevents configuration until firmware load is finished and
is_initialized() returns true.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9998 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Support enabled for the vpmoct032 echo cancellation module for the wctdm24xxp
and wcte12xp drivers.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9997 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In previous releases of DAHDI if dahdi_cfg attached a software echocan
to a channel and a hardware echocan was available, the hardware echocan
would be used instead of the software echocan.
Since the 2.4 branch was created a new feature was merged into
dahdi-linux where it was possible to mix software echocan and hardware
echocan on a channel. This required using "hwec" as the echocan in the
/etc/dahdi/system.conf file so that what was specified in the
configuration file is what was actually used.
This has resulted in users upgrading to the trunk of dahdi without
updating their /etc/dahdi/system.conf file and just suddenly not using
any hardware echocans any longer.
The capability to mix software and hardware echocans on a span will be
revisted when running dahdi_cfg on any preexisting configuration files
doesn't just silently turn off hardware echocan.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9995 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* xpd_echo (card_echo.c) - a module to handle an Astribank hardware echo
canceller module.
* All other XPDs are now of type 'telephony_device'. Only a telephony device
XPD provides a span to register.
* The EC module will typically show up as XPD-40 and will always show up as
Unregistered in 'dahdi_hardware -v'
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9993 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reverts commit r9891 and is part of two commits to revert all the
timer changes.
Grouping the timer into rates did not allow a timers rate to be changed
after another thread is already blocked on the poll call
The problem that was reported was if a sip call was made to a DAHDI
channel and the sip call was disconnected before answer, the DAHDI
channel would never stop rining.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9991 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reverts commit r9937 and is part of two commits to revert all the timer
changes.
Grouping the timer into rates did not allow a timers rate to be changed after
another thread is already blocked on the poll call
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9990 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Linux kernel v2.6.22 introduced the __packed macro to allow the gcc specific
__attribute__((packed)) extension to be overridden if required and
checkpatch.pl will complain if you don't use it.
For some strange reason gcc doesn't complain when you use non-existant
decorators.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9989 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r9946, "wcte12xp: Move the VPMADT032 test/configuration to module load
time." introduced a race condition where it was possible for the timer
that initiates the check for the alarms to fire before the board was
marked initialized. This would result in a board that would never again
check it's alarm state since the first time the timer runs INITIALIZED
may not be set and it will not reschedule a check since it believes the
driver is unloading.
This happened because the check for the VPM was moved between when the
timer was first setup and when INITIALIZED was then set.
Now we make sure INITIALIZED is set before the timer is first setup, and
move those two operations together.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9981 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In commit r9968 "wctdm24xxp: Allow more than one outstanding read at a
time" I introduced a regression where the transmit FIFO on the data
channel of a B400M could get locked up. The result would be constant
HDLC overflows when writing to the data channel.
This regression did not make it into any releases and did not exhibit
itself when crossing spans on a single B400M module. This is a partial
revert of commit r9968.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9977 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The board number dupliates the information that is available in the
location field. Exporting it as part of the description makes the name
dependent on the driver bind order which is not desirable.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9971 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Updates the CMD_BYTE macro to use precalculated offsets.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9970 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since every read needs to go through the complete voicebus pipeline, if
we know we're going to read multiple bytes we can queue them all up.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9968 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Saves time in the interrupt handler by eliminating the need to scan
through all of the slots in the cmd arrays. Also allows the reads from
ISR context to automatically grow as the latency grows. This ensures
that battery and hook state is actually checked every frame like
originally intended.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9966 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Trivial reformatting that preps it for some parallelizing the module
loads.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9965 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The card position is only used during startup so we don't need to carry it
around in the strucuture.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9964 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The voicebus cards only support the S110M FXS modules which are based on
the 3215. The module flags member was only used to hold whether we were
dealing with a 3210 or 3215 SLIC, so we can drop it since we always know
we'll have a 3215 based SLIC.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9963 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Cuts down on the overhead of constantly saving and restoring the
interrupt registers.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9962 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change gets all the easy places and saves on array dereferences
when we already have the address of the module that we are interested
in.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9961 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change is to primarily to clarify that the types are always mutually
exclusive.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9958 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This also allows us to add them to the union with the other module types so
they do not add to the memory usage if there aren't any QRV modules installed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9957 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Move the data backing the mostly unused string away from the active
members of 'struct wctdm'.
The location where some of the other members of 'struct wctdm' are initialized
were moved so that wctdm_back_out_gracefully always has a fully formed
structure to work on.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9955 a0bf4364-ded3-4de4-8d8a-66a801d63aff
We can already use the module type to determine presence of a module to
check. This also moves the background polling of the modules until after
the board is completely initialized because the module type may change
while the different types are being probed. This also means that we need
to preset the shadow registers for the FXS because otherwise the shadow
register will not have been read before the first time it's checked for
a power alarm.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9954 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Both limit the amount of junk in the kernel log and also prevent dahdi_cfg
from running indefinitely if there is a module with a hardware problem which
prevents it from completing the startup sequence.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9953 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Part of increasing system startup speed.
Splitting these two operations facilitate checking if there is a module
present synchronously on driver load from the actual load of the firmware and
configuration of the channels.
This will allow the presence of the VPM module to be flagged on the span
before registration, but load and configuration can happen in the background.
When the modules are eventually loaded via udev, there will be enough time
from the time the drivers are loaded to when dahdi_cfg will run to complete
the firmware load, eliminating the need to block the driver here.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9951 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In my opinion naming the VPM workqueues for each board is not worth the
extra complexity.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9950 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Ensures that a single run of the interrupt service routine is consistent
about whether there are VPMADT032 commands to process or not.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9949 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This message also duplicates what is in the /etc/dahdi/system.conf file
and should only be necessary when troubleshooting problems.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9948 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is trivial cleanup. Fixing up a couple of places that followed a
kmalloc with a memset to 0 and also sneaked in one ARRAY_SIZE usage
change.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9947 a0bf4364-ded3-4de4-8d8a-66a801d63aff
