Saves about a 1us on average from the interrupt handler on one test
system.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10239 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Eliminates the need to store a copy of the flags and variety from the
global devtype.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10238 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'memaddr' and 'memlen' is already cached as part of the underlying pci
device so the wct4xxp driver does not need to cache it again. 'canary',
'passno', 'master', and 'oct_rw_count' are unused.
In t4_span 'irqmisses' was incremented, but never used anywhere, and there is
already the irqmisses on the span itself.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10237 a0bf4364-ded3-4de4-8d8a-66a801d63aff
I was unable to measure a performance change with prefetching.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10236 a0bf4364-ded3-4de4-8d8a-66a801d63aff
We are already in hardirq context and can therefore save the cli/sti
call.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10235 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Speeds up these calls primarily by eliminating unnecessary flushes
of writes to the PCI bus.
Before:
7.095 us | __t4_framer_in();
5.835 us | __t4_framer_out();
7.122 us | __t4_framer_in();
7.071 us | __t4_framer_in();
7.059 us | __t4_framer_in();
5.859 us | __t4_framer_out();
7.076 us | __t4_framer_in();
5.852 us | __t4_framer_out();
7.124 us | __t4_framer_in();
7.080 us | __t4_framer_in();
After:
1.694 us | __t4_framer_out();
1.686 us | __t4_framer_out();
1.695 us | __t4_framer_out();
3.182 us | __t4_framer_in();
3.283 us | __t4_framer_in();
2.889 us | __t4_framer_in();
2.942 us | __t4_framer_in();
2.951 us | __t4_framer_in();
2.906 us | __t4_framer_in();
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10234 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The 'pedanticpci' module parameter, which is always on by default,
inserts extra reads from the card in order to ensure that all writes are
properly flushed through any PCI bridges which may post the writes. The
side effect is that this takes more CPU time for registers reads and
writes, especially to the framer registers.
It is never recommended to run with pedanticpci set to 0, so I'm
removing it as a module parameter so that the default case does not take
a performance hit checking for whether the parameter is set or not.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10233 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Also has the nice side effect of eliminating a comparison from the
interrupt handler.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10232 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The overhead of reading the framer registers is significant and can
result in latency bumps / data drops on heavily loaded systems.
Instead of checking all spans every millisecond when they are in
alarm we will instead only check every 100 ms.
On one test system, dropped the % CPU time spent in hard interrupt
context from 10% per TDM4XX when all four spans are in alarm to
closer to 2%.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10231 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is the "normal" condition and can be lumped with the other
informational messages. Otherwise, just this one message might go to the
console depending on the system configuration which can be confusing.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10230 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This value is not used and is now gone.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10229 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r10160 "wctdm24xxp: Probe for and configure modules in parallel."
did not properly setup the VPMADT032 for all ports on hybrid cards.
The most immediate sympton being that spans 3 and up on a hybrid
card would not come up in Asterisk even though they were out of
alarm. This was because the echo canceler was blocking messages on
the dchannels.
This does not affect any previously released versions of DAHDI-Linux
or users of the VPMOCT032.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10228 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Uses the linecompat member to determine what type of span it is. This will
allow removing T1/E1 flags from other places where the span type is stored.
This function also changes the return value from bool to int for the
inlines defined in include/dahdi/kernel.h. This is because not all
kernel versions include stdbool.h in the headers and it will conflict
with boolean values that are exported via module parameters on some
older kernels if dahdi included it globally.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10227 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The pr_ macros are the recommended way for subsystems to print messages
but not all kernel versions DAHDI support has them defined.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10226 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Commit r9750 "wct4xxp: Reduce the memory footprint of the hardware
echocanceler.", as part of reducing the non-pageable memory required to
support the VPMOCT064 and VPMOCT128, disabled caching of some hardware
echocan registers. This resulted in more physical reads to the echo
canceler. These new read transactions exposed an existing issue where
sometimes reads could be turned into writes which put a channel into an
unintended state preventing Asterisk from detecting any DTMF.
This issue is resolved by ensuring that the write signal to the Octasic
part is explicitly cleared between when the address is presented on the
bus and when the read and chip select signals are asserted. The cost is
an increase in the average time to enable / disable echo cancellation by
about 5 us on one Intel Xeon X3220 test machine (~250ns increase per
read from the Octasic part and 20 reads to enable / disable a channel).
This commit resolves a behavioral regression first introduced in 2.5.0
and 2.4.1 which could take many calls before revealing itself. This
change only affects cards with a VPMOCT128 or VPMOCT064 installed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Doug Bailey <dbailey@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10220 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The driver has, until now, dropped G723 SID frames even though the
firmware on the TC400/TCE400 can handle them. Now let them on
through.
Reported-and-Tested-by: Angel Carhuas <acarhuas@colinanet.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10218 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The intent here is to flag to users that the maintenance counters are
not collected for spans exported by the wcte12xp driver.
dahdi_maint before this change:
# dahdi_maint -s 1
Span 1:
>Framing Errors : 0:
>CRC Errors : 0:
>Code Violations : 0:
>E-bit Count : 0:
>General Errored Seconds : 0:
And after:
# dahdi_maint -s 1
Span 1:
>Framing Errors : -1:
>CRC Errors : -1:
>Code Violations : -1:
>E-bit Count : -1:
>General Errored Seconds : -1:
This can be combined with a change to dahdi_maint to recognize that the
errors are -1 and print an even more explicit warning.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10212 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Currently, the devicetype string was set both when the device was first
allocated and updated when an echocanceler was detected. For simplicity,
combine both these steps into a single function.
This change also replaces an improper use of strncat with strlcat.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10210 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* 'D' DTMF digits were accidentally discarded with the notice message:
"Bad DTMF value 0. Ignored".
* No need for an odd 1-based translation table anymore - it's 0-based.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10209 a0bf4364-ded3-4de4-8d8a-66a801d63aff
There were a couple of reports that MeetMe conferences were not
working in 2.5.0.1 and that downgrading to 2.4.1.2 resolved the
issue. This could occur if there were no analog spans in a system,
and all the digital spans were out of alarm before DAHDI_STARTUP
ioctl was called by dahdi_cfg. If the spans were *not* out of alarm,
they would be marked master when the span changes it's alarm state.
This would result in a condition where no spans were marked as the
"master" and so the core timer was handling conferencing. The core
timer runs by default at 4ms and most board drivers run at 1ms
intervals, but a channel currently only buffers up 2ms of data when
conferenced. Therefore, 2ms of audio from a board was continuously
dropped from the conference every 4ms by default.
This fixes a regression first introduced in 2.5.0 which was
specifically added in revision r9611 "dahdi: Do not locate new
master in interrupt context."
Internal-reference-ID: DAHDI-894
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Tested-by: Dennis Martinez <dmartinez@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10205 a0bf4364-ded3-4de4-8d8a-66a801d63aff
These members are not used anywhere and are now gone.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10204 a0bf4364-ded3-4de4-8d8a-66a801d63aff
A "(VPMADT032)" string is appended to the devicetype (as shown by
dahdi_scan) for the span if one is installed. Now append '(VPMOCT032)'
if one is installed as well.
Also, for the wcte12xp driver append the VPM name to the device type after
initially probing as opposed to only after the span is configured.
(Related to issue DAHDI-890)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10203 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Bug sympthoms: wrong FSK VMWI sent few seconds after
offhook. That was caused because the driver kept
polling the (physically unconnected) digital inputs.
[note: a workaround for drivers without this patch
is to zero the 'xpd_fxs.poll_digital_inputs' parameter.]
* Also, the digital_inputs/digital_output masks were
calculate using a different condition.
* Now we determine number of channels, digital inputs and
digital outputs in a single place and use this info
later to calculate the correct masks.
* We poll only if there are digital_inputs
* We added a sanity check in process_digital_inputs, so
we get a notice if it's called on an xpd without digital
inputs (e.g: hypothetic firmware bug).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10202 a0bf4364-ded3-4de4-8d8a-66a801d63aff
DAHDI currently waits a second before checking if a board driver is
calling dahdi_receive and switching to internal timing. Some versions of
Asterisk (I was looking at 1.4.42 when writing this) only wait 300ms for
a timer to expire when first starting and verifying that DAHDI is
properly configured. This can result in a
"ERROR[27673] asterisk.c: Asterisk has detected a problem with your DAHDI
configuration and will shutdown for your protection. You have options:"
message if asterisk is started soon after loading DAHDI.
This change sets the inital polling interval to the same as that used
during normal coretimer operation, 4ms. The interval will still be
slowed to 1 second if a board driver starts calling dahdi_receive().
DAHDI-892.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10200 a0bf4364-ded3-4de4-8d8a-66a801d63aff
New firmwares to handle the new 2FXS/6FXO module.
FPGA_1161.hex, PIC_TYPE_1.hex, PIC_TYPE_2.hex of internal rev. 9732
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10179 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Firmware version 1.11.0 resolves an issue where the driver fails to
detect certain VPMOCT032 modules after a cold boot.
Signed-off-by: Doug Bailey <dbailey@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10172 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The driver / FXO modules now always operate in a fwringdetect mode and the
module parameter was never checked anywhere. It is now gone.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10171 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Eliminate the assumption that the check function is going to be called
for every frame. Also use a state machine to make polarity debouncing
similar to the other debouncing code.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10170 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Allows the driver the option of not calling the misc function for every
frame. This is part of preparation for moving misc processing out of
the interrupt handler. Also use a state machine for the various battery
states to unify the technique for debouncing the various signals in the
driver.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10169 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Do not assume the ring detection function is called for every frame.
Also change the debounce logic to a state machine to clarify what state
a port is in and unify the technique for debouncing the various signals.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10168 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Part of moving more of the module specific processing out of the
interrupt handler and allowing the interrupt rate to be slowed down.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10167 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Part of preparations for being able to optionally slow the interrupt
rate down and opening the door for moving more module processing out of
the interrupt handler.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10166 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Saved me time when reading the code so I don't have to lookup which position
in the index is what register for each of the modules.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10165 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The variable does not necessarily have anything to do with the frequency
of interrupts but is instead a count of sframes received. For example,
it is possible to slow the interrupt rate down on the voicebus cards to
one every 2 frames.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10164 a0bf4364-ded3-4de4-8d8a-66a801d63aff
We can spend less time in interrupt context by not saving and restoring the
local interrupt state. This is a particularly noticeable improvement on debug
kernels with lockdep.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10163 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Closes a small window of opportunity where one CPU might free a VPM
instance that the interrupt handler may currently be using.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10162 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Wait until we have de-bounced the presence of battery before moving on the
check for changes in polarity. This removes the sometimes random
polarity messages generated on an FXO port when the far side drops
battery from a supervisor disconnect.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10161 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Use the newly create bg_create and bg_join to actually probe / configure
groups of 4 modules in parallel. This currently has to be done in groups
of four due to the way 4-port modules are identified relative to single
port modules.
This provides a dramatic improvement in driver load time. When loading a
single TDM2400 with 24 FXS ports before this change:
# time modprobe wctdm24xxp vpmsupport=0
real 0m46.674s
user 0m0.000s
sys 0m0.520s
And after this change:
# time modprobe wctdm24xxp vpmsupport=0
real 0m7.900s
user 0m0.000s
sys 0m0.070s
Note that the boards themselves are still configured serially. Board
configuration can be parallelized once the assignment of board position
is moved out of the function that is run in parallel. Otherwise it could
be possible for board numbers to switch on repeated loads.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10160 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Create a generic facility to spawn tasks to run in parallel. There are
interfaces already in the kernel for doing this, but they are not
supported on the full range of kernels that DAHDI must support.
This will be used to identify and configure FXS/FXO/B400M/VPM modules in
parallel.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10159 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When the driver begins to initialize a device it conducts a read/write
test on one of the framer registers. The driver ignores the result of
that test and results in much output spammed to the kernel logs for a
failed card since the driver doesn't then try to unbind from the device.
What was getting spammed:
wcte12xp 0000:03:01.0: Timeout in t1_getreg
wcte12xp 0000:03:01.0: Wrote '0' but read 'fffffffb'
Now abort the bind if the read / write test fails.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10155 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If LIVE_DAHDI_FREEPBXDB=yes is set in live.conf, live_dahdi will also
generate FreePBX astdb entries for the FXS entensions it probed (using
the dahdi_genconf module freepbxdb).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10151 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r10006 "wctdm24xxp: Add 'fastpick' module parameter." copied the
fast-off hook module parameter from the wctdm.c driver, but the setting
in that driver does not match the data sheet. The previous commit did
not actually change any of the significant bits in that register. Also,
that commit changed the timer, but did not disable the callibration
delay which is necessary for Type-II callerid.
The fastpickup option in the wctdm24xxp driver should now match the
fastpickup option in the wctdm driver.
DAHDI-224.
Reported-By: Kinnith Wallace <kwallace@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10148 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Really only *necessary* when SLAB debugging is enabled, but in that
case, can reduce the chance of latency bumps when first loading the
driver. Otherwise the constant slab poisoning / checking in interrupt
context from the kmalloc / kfrees is too much.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10144 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The logic loops through the static cards[] array to determine timing,
but the subloop was based off the current card's numspans member.
This could cause a null dereference in the case where two cards of
different span densities were connected via timing cables.
Reported-by: Doug Bailey <dbailey@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10140 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r10082 "wctc4xxp: Cleanup in-flight commands when halting due to
hardware error." introduced a lock imblance on the error path where the
cmd_list_lock would be unlocked twice when the board is halted due to a
hardware error. Thanks sparse.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10138 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r10066 "wctdm24xxp, wcte12xp: Run the ISR with interrupts disabled."
requested that the interrupt handler be run in "fast" mode (disabled)
but this isn't necessarily guaranteed.
This patch makes the interrupt handler itself disable all the interrupts.
Linux commit 470c66239ef0336429b35345f3f615d47341e13b [1] contains a comment
about why this is necessary.
[1] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=470c66239ef03364
(closes issue DAHLIN-248)
Reported-and-Tested-by: Vladimir Mikhelson <vlad@mikhelson.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10118 a0bf4364-ded3-4de4-8d8a-66a801d63aff
