`struct timeval` has been removed from the kernel interface in 5.0 as
part of fixing the 2038 problem. ktime_t is the preferred kernel time
interface now.
Signed-off-by: Shaun Ruffell <sruffell@sruffell.net>
There are not any major distributions that are still supporting kernels
older than 2.6.27 so we can remove many typedefs. The primary motivator
for this change is that kernel 5.0 is dropping support for timeval and
it would be ideal if the in-kernel time representation can
standardize on ktime_t, but 2.6.18 did not support the ktime
interface that was needed.
Signed-off-by: Shaun Ruffell <sruffell@sruffell.net>
The xpp drivers were originally developed seperately and thus had their
own version number. For quite some time they no longer have this version
number and report 'Revision: Unknown'.
Get rid of this mechanism.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
The xpp modules use time differences for various statistics. In one case
xpp_usb creates a histogram of the time it took the system to send USB
packets (URBs). The time difference is used (after adjustments) as an
index to that array.
However if the clock happens to go back at that exact point in time, we
get to write to an arbitrary negative index in this array.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
* Drop PCM during sluggish events:
- Drop both rx/tx (was only tx)
- Drop almost all pcm until sluggishness stops (used to drop only
single pcm each time).
- Renamed: "drop_next_pcm" -> "drop_pcm" (to match new semantics)
- Still allow "keep alive" PCM so Astribank will not reset FXS high-voltage.
The "sluggish_pcm_keepalive" parameter set the rate (1/50 by default)
- Added rx/tx drop statistics counters
- Removed "pcm_tx_drops" (replaced by new statistics counters)
* Also improved format of /proc/xpp/XBUS-*/xpp_usb:
- Show cummulative number of sluggish events.
- Clearly show range (in usec) of usb_tx_delay[]
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
This is needed to compile against Linux 3.10.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
[tzafrir.cohen@xorcom.com: fixed passing /proc/xpp/XPD/summary xbus number]
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Cc: Russ Meyerriecks <rmeyerriecks@digium.com>
Cc: Oron Peled <oron.peled@xorcom.com>
This patch removes support for kernel versions < 2.6.18, as those are
not actively supported in any major Linux distribution (except RHEL4,
which is in the "extended" support level of the product life cycle).
This removes much of the more #ifdef-rich parts of the code.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10472 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* An xbus transport now have a "model_string" member
* The xpp_usb driver fills this with "usb:<idVendor>/<idProduct>/<bcdDevice>"
* It is passed via environment to the "init_card_<type>_<protocol>" scripts
* The FXS script uses this to condition two registers according to
the power supply model.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10300 a0bf4364-ded3-4de4-8d8a-66a801d63aff
gcc-4.6 now warns about variables that are set but never used. Clean up
unused variables everywhere except the oct612x subdirectory.
The oct612x should go in a separate patch in case that needs to be
pulled out into a separate project again.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9929 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Mostly linux/errno.h was included more than once.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9557 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Using semaphores as mutexes was removed from the kernel in 4882720b267b.
Just use straight semaphores now. 'DECLARE_MUTEX()' -> 'DEFINE_SEMAPHORE()'
and 'init_MUTEX()' -> 'sema_init()'.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
LKML-Reference: <20100907125057.562399240@linutronix.de>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9464 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The check for DEFINE_SPINLOCK was spread throughout the source tree. If
not defined we can just define it in inlucde/dahdi/kernel.h. Now
include/dahdi/kernel.h is the only place that references
SPIN_LOCK_UNLOCKED (which breaks lockdep checking if DEFINE_SPINLOCK is
otherwise defined in the kernel).
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Review: https://reviewboard.asterisk.org/r/940/
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9411 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This needs some more testing before it's on by default. If the card is
otherwise functioning, these messages may be confusing to the user. If
the card is not functioning, the driver can be reloaded with debug to
check for this condition.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9205 a0bf4364-ded3-4de4-8d8a-66a801d63aff
