When attaching software echocans to a channel, if there is a hardware
echocan available always give preference to them.
Revision 9995 "dahdi: Always attach hwec to a channel if available" had
an error where if a driver did not even support an option of hardware
echocan, dahdi-base would take that to mean there always was a hardware
echocan available on the channel.
DAHLIN-246
Reported-by: Michael L. Young
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10070 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Revision 9886, "wcte12xp: Use the in-hardirq versions of
dahdi_receive/dahdi_transmit", changed the call into dahdi_receive and
dahdi_transmit to use versions that assume local interrupts are already
disabled. Not all versions of the kernel run interrupt service routines with
all interrupts disabled and therefore it was possible to lock up a CPU with a
recursive grab of the chan_lock.
When LOCKDEP was enabled (on debug kernels) interrupt handlers were run
atomically so this problem would only occur on pre 2.6.35 kernels that did not
have lockdep enabled.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10066 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The wcte12xp wasn't recognizing loopup/loopdown signals. The debounce was so
long that it was preventing the loopup/loopdown signals from being registered
properly. Removed the debounce entirely as it was unnecessary to the operation.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10064 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Revision 9750 "wct4xxp: Reduce the memory footprint of the hardware
echocanceler" reduced the number of bits used to store some structure
members. Some of the new field lengths were unable to store all the
possible values the API as used assigned to the fields, resulting in
channels never entering power down mode when they were disabled like
they were previously.
The change for byEchoOperationMode was found in testing the operation of
the VPMOCT032 which currently uses the same code. The others were done
via a review of the API doc.
This change represents negligable risk and contains no logic changes.
It only increases the memory footprint of the API instance in the
kernel.
Signed-off-by: Doug Bailey <dbailey@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10060 a0bf4364-ded3-4de4-8d8a-66a801d63aff
live_dahdi: Add a new command: symlink_ast, to make the system's
/etc/asterisk/dahdi-channels.conf a symlink to the one generated by
'reload' / 'genconf'.
If the system dahdi-channels.conf is a generated one and has not edited,
there's no real harm with running this.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10057 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Make sure that the call to dahdi_chan_unreg() in free_pseudo() is
protected by the registration_mutex, like the other calls to that
function.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-By: Oron Peled <oron.peled@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10056 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Required by CAS in latest (2.5) DAHDI versions.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10055 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This avoids a nag about a meaningless single-bit signed int.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10054 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If the CPU becomes overly busy, merely printing the "Overflow in the
recieve_queue" messages becomes CPU-intensive on its own right.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10052 a0bf4364-ded3-4de4-8d8a-66a801d63aff
/etc/asterisk already gets generated at config. No need to re-create it
at genconf time.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10050 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The shutdown logic requires that all CPUs see that the INITIALIZED bit
has been cleared. Otherwise it may be possible for the workqueue to run
after the hardware resources have been released.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10047 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If the OCT6104E-256D.ima Octasic firmware was downloaded to the build
directory, install it over with the rest of the firmware files.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10038 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If set to true (default) a HWEC, if available on the channel, takes
priority over any software echocan configured in /etc/dahdi/system.conf.
This has historically been the default behavior in all released versions
of DAHDI that support module echocans.
Otherwise, hwec_overrides_swec is set to false, HWEC is chosen only via
the "echocanceller=hwec" directive.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-By: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10036 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Make sure you have etc/asterisk in the live tree before generating
configuration.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10028 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This adds module parameter 'ring_trapez'. When set, the wave form of
the ring tone is set to be a trapezoid, rather than sine. Thus making
the ring stronger.
This is a boolean parameter of the module xpd_fxs. Takes effect at the
beginning of the next ring.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10022 a0bf4364-ded3-4de4-8d8a-66a801d63aff
gcc 4.6 complains about variables that are assigned values but then
never used.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10020 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In some cases the hardware echo canceller cannot be used. Mostly related to
an FXO module.
* FXO module if the first module is BRI or PRI
* FXS module if the Astribank has another FXO, no PRI/BRI, and is a sync
slave.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10019 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r9943 enabled the presence of hardware EC to be probed on a card. That
change did not account for wcb4xxp based cards that did not have a
hardware echocan on board.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10017 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The dual and quad span cards have a rotary switch onboard which controls
the order that cards serviced by this driver are registered with the
core of DAHDI. This commit adds a module parameter 'ignore_rotary'
which, when set to 1, causes the driver to ignore the position of the
rotary switch and only consider the physical slot when registering with
DAHDI.
Ignoring the rotary switch settings also permits the PCI device to be
bound and unbound from the driver at runtime since registration with
DAHDI no longer only happens when the module is first initialized.
By default, the rotary switch will still be used to determine
registration order. This commit does not change the default behavior.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10016 a0bf4364-ded3-4de4-8d8a-66a801d63aff
New Astribank II FPGA firmware and USB firmwares that add support for the
hardware echo canceller module.
Note that due to a bug in previous FPGA firmwares, an Astribank with such
older firmware and with a hardware echo canceller module will not have any
functioning audio at all.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10013 a0bf4364-ded3-4de4-8d8a-66a801d63aff
I failed to compile the commit exactly as it was committed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10008 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When true / 1 the FXO port will use a shorter off-hook calibration
delay. This is sometimes necessary in order to properly decode Type-II
Caller ID information which is sent shortly after an FXO port goes off
hook.
Defaults to 0 unless opermode is "JAPAN" then it will default to 1. This
functionality was ported from the wctdm.c driver.
DAHDI-854.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10006 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If an FXS port is configured to use kewl start signalling, when the FXS port
is "hungup" it should drop battery for 500ms so that any attached devices can
detect that the remote side has disconnected. The wctdm24xxp driver
since version 2.4.0 was only dropping battery for ~5-10 ms because it would
set "open" on the line, but then the next time it read the line feed register
state, it was setting the LINE feed register to the idle state.
This change checks if the line is forced open before setting the FXS port back
"onhook" so as to not turn on battery prematurely.
This fixes a regression introduced in r9070 "wctdm24xxp: Prevent FXS Proslic
staying in "Forward/Reverse OnHookTransfer...". DAHDI-849.
Checking for open on the line feed registered was originally suggested by Alec
Davis.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10002 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reverts commit r9879. Asterisk commit r264249 [1], which was committed
after the switch to enumerations, requires the maintenance modes to be
Changing the test in configure.ac from:
AST_C_DEFINE_CHECK([DAHDI], [DAHDI_RESET_COUNTERS], [dahdi/user.h], [230])
to:
AST_C_COMPILE_CHECK([DAHDI], [int foo = DAHDI_RESET_COUNTERS], [dahdi/user.h])
Would allow the maintenance modes to stand as enumerations but the potential
for users to run incompatible versions does not seem worth it at this point.
[1] http://svnview.digium.com/svn/asterisk?view=revision&revision=264249
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10000 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The firmware load has been moved into a workqueue to prevent the module load
from blocking for the duration of the firmware upload. This could be up to 40
seconds. Driver prevents configuration until firmware load is finished and
is_initialized() returns true.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9998 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Support enabled for the vpmoct032 echo cancellation module for the wctdm24xxp
and wcte12xp drivers.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9997 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In previous releases of DAHDI if dahdi_cfg attached a software echocan
to a channel and a hardware echocan was available, the hardware echocan
would be used instead of the software echocan.
Since the 2.4 branch was created a new feature was merged into
dahdi-linux where it was possible to mix software echocan and hardware
echocan on a channel. This required using "hwec" as the echocan in the
/etc/dahdi/system.conf file so that what was specified in the
configuration file is what was actually used.
This has resulted in users upgrading to the trunk of dahdi without
updating their /etc/dahdi/system.conf file and just suddenly not using
any hardware echocans any longer.
The capability to mix software and hardware echocans on a span will be
revisted when running dahdi_cfg on any preexisting configuration files
doesn't just silently turn off hardware echocan.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9995 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* xpd_echo (card_echo.c) - a module to handle an Astribank hardware echo
canceller module.
* All other XPDs are now of type 'telephony_device'. Only a telephony device
XPD provides a span to register.
* The EC module will typically show up as XPD-40 and will always show up as
Unregistered in 'dahdi_hardware -v'
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9993 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reverts commit r9891 and is part of two commits to revert all the
timer changes.
Grouping the timer into rates did not allow a timers rate to be changed
after another thread is already blocked on the poll call
The problem that was reported was if a sip call was made to a DAHDI
channel and the sip call was disconnected before answer, the DAHDI
channel would never stop rining.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9991 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reverts commit r9937 and is part of two commits to revert all the timer
changes.
Grouping the timer into rates did not allow a timers rate to be changed after
another thread is already blocked on the poll call
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9990 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Linux kernel v2.6.22 introduced the __packed macro to allow the gcc specific
__attribute__((packed)) extension to be overridden if required and
checkpatch.pl will complain if you don't use it.
For some strange reason gcc doesn't complain when you use non-existant
decorators.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9989 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r9946, "wcte12xp: Move the VPMADT032 test/configuration to module load
time." introduced a race condition where it was possible for the timer
that initiates the check for the alarms to fire before the board was
marked initialized. This would result in a board that would never again
check it's alarm state since the first time the timer runs INITIALIZED
may not be set and it will not reschedule a check since it believes the
driver is unloading.
This happened because the check for the VPM was moved between when the
timer was first setup and when INITIALIZED was then set.
Now we make sure INITIALIZED is set before the timer is first setup, and
move those two operations together.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9981 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In commit r9968 "wctdm24xxp: Allow more than one outstanding read at a
time" I introduced a regression where the transmit FIFO on the data
channel of a B400M could get locked up. The result would be constant
HDLC overflows when writing to the data channel.
This regression did not make it into any releases and did not exhibit
itself when crossing spans on a single B400M module. This is a partial
revert of commit r9968.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9977 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The board number dupliates the information that is available in the
location field. Exporting it as part of the description makes the name
dependent on the driver bind order which is not desirable.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9971 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Updates the CMD_BYTE macro to use precalculated offsets.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9970 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since every read needs to go through the complete voicebus pipeline, if
we know we're going to read multiple bytes we can queue them all up.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9968 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Saves time in the interrupt handler by eliminating the need to scan
through all of the slots in the cmd arrays. Also allows the reads from
ISR context to automatically grow as the latency grows. This ensures
that battery and hook state is actually checked every frame like
originally intended.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9966 a0bf4364-ded3-4de4-8d8a-66a801d63aff
