The ioctls for the debug network interface on the tc400b0 has not been used for
a long time. It is now gone.
This will also allow the sempahore set in the ioctl to be changed into a mutex
which provides enhanced debugging checks.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
When an unsolicited alert is received, we'll flag the card as halted so that
commands will not be retried. This is because often times the firmware will no
longer process any commands in this state and the driver will hold processes in
the dstate while waiting to retry the commands.
This is a debugging aide in that it simplies unloading the driver if the card /
driver is currently in a failed state.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
The read-line-multiple command was already disabled on the voicebus cards, which
use the same interface, in commit 4de462c3e0. This
does the same thing for the transcoder card and also disables the read line
command.
I've seen this change directly correlated to problems with the AN983 receiving
packets from the onboard DSP on some platforms.
Internal-Issue-ID: DAHDI-1071
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
I've not seen this directly tied to any issue, but it's enabled on the voicebus
cards and so brings the wctc4xxp driver in line.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Fixes regression from bb63d03bba (before
v2.7.0). This failed to set the PCM mask on a CAS span when
DAHDI_AUDIO_NOTIFY was not set.
As the first channel of each xbus would be enabled (for
synchronization), a single call may still have passed.
This patch sets the PCM mask on any CAS channel explicitly.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
* It's currently harmless (just re-run the pre/post XPD registrations)
* But it's cleaner this way (as with xbus_register_dahdi_device())
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
XPP devices have implicit support for device registration and
unregistration. Even though it is only used for the legacy (non-hotplug)
configuration case, we still prefer to make it explicit.
This attribute would later allow a simpler implementation of the user
space (xpp-specific) tool dahdi_registration.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
In an Astribank with >= 2 PRI ports, switching from E1 to T1 at run-time
may fail at the DAHDI_CHANCONFIG ioctl on the first channel in a span,
That is, on first run of dahdi_cfg, it fails on second span, on second:
it fails on third span, etc.
The code clears the D-channel information on the DAHDI_CHANCONFIG call
for the first channel in the span.
However The code tested for the global "channo" rather than the per-span
"chanpos" to check for the first channel in the span. This the test
failed.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
This is to support users who are unable to update to the lastest CentOS 5.x.
There is no change for most users on the latest releases of their distribution.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
The timer_list member of the transcoder buffer has not been used for a long
time. Saves some space in the buffer in addition to removing any future
curiosity about what it is for.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
If the memory allocation for the new channel array fails, it would be possible
to call enable_irq() without the corresponding call to disable_irq().
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This fixes a regression introduced first in release 2.9.1 with commit
(7ce8498465 "firmware: Refactor by using build_tools/install_firmware.")
which prevents from installing the firmware in a location other than the system
root.
Bug: https://issues.asterisk.org/jira/browse/DAHLIN-337
Reported-by: Anthony Messina <amessina@messinet.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
[edited the commit message]
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
* dahdi_registration writes multiple times to:
/sys/bus/astribanks/devices/*/*/span
* In some race cases this resulted in corruption and eventual kernel
panic.
* Until migration to "assigned-spans" is complete:
- Accept and ignore multiple "dahdi registrations" from user-space.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
When the card goes through a reset the PCIe link will be brought down. Some
slots will report this change upstream to the root port which will believe that
the card has been hotplugged out of the system.
This fixes cases on some systems where, during a firmware update, the card gets
removed from the system's logical PCI tree with messages like the following in
the kernel log:
pciehp 0000:00:1c.0:pcie04: Card not present on Slot(259)
pciehp 0000:00:1c.0:pcie04: Card present on Slot(259)
Internal-Issue-ID: DAHDI-1091
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This firmware image is able to handle system conditions that would result in
spans internmittenly going down and recovering.
Internal-Issue-ID: DAHDI-1087
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
These firmware images can handle system conditions that would previously result
in transmitted audio being intermittently silenced and then unsilenced.
Internal-Issue-ID: DAHDI-1087
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This firmware image is able to handle system conditions that would result in
spans going down and then coming back intermittently.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
There are some platforms where the DMA operation to the host does not complete
within the required 50us. When this happens some versions of the firmware will
issue a retry and increment the retry field in the descriptor status word.
Now if this driver is configured in DEBUG mode, the presence of these retries
will be printed to the kernel log as a potential troubleshooting aide.
Internal-Issue-ID: DAHDI-1087
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
There are error conditions that the firmware can detect but cannot recover from
without help from the driver. When firmware detects these conditions the
DESC_IO_ERROR bit will be set in the descriptor header to signal that the driver
should reset the TDM engine on the card. Since this is not due to failure of the
host to service the interrupt in time, it does not make sense to increase
latency when these conditions are detected.
Internal-Issue-ID: DAHDI-1087
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Without this change it's hard to see what is actually running on the card when
the firmware in the flash doesn't match the reported version. This is a
debugging aide.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This allows a .tar.gz file that is normally downloaded from the server to be
checked directly into a test branch. Now when the firmware is being installed,
it can be extracted from any present .tar.gz. Again, this is primarily to
simplify testing.
A nice side effect is that when going from a newer version to an older version,
any stale .bin files in the firmware directory will not be installed into
/lib/firmware, but instead the bin file from the *versioned* .tar.gz will always
be installed. This should reduce problems where you have to run "make
dist-clean" when reverting to an older version that has a firmware change.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This is intended to simplify the Makefile and move a large common part into a
subscript. The behavior is the same as it was before.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
* We didn't handle proper E1/T1 transitions after device registration.
* Fix SPAN_REGISTERED(xpd):
It now checks for DAHDI_FLAGBIT_REGISTERED as well, as this flag is
set/clear by assign/unassign.
* From set_pri_proto():
- Always free/allocate channels
- Always call dahdi_init_span()
* Improve phonedev_cleanup() safety:
- NULL pointers after free.
- Zero number of channels at the end.
* Refactor channel allocation out of phonedev_init():
- Into phonedev_alloc_channels()
- Also called from xpd_init_span() to prevent duplicated logic.
- And called from set_pri_proto() to prevent our bug.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Commit 74e949c33a exported the module
variable dahdi.auto_assigned_spans. However this is not a good name.
This commit reverts the export and replaces it with a new function to
get the value of the variable.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
A fix to 03b3ce1a10: use ktime_get_ts
instead of getnstimeofday to better handle system time changes.
(Shaun Ruffell)
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Add a new sysfs attribute to dahdi_device: registration_time
* Records the time of the device's registration with DAHDI.
* Used by dahdi_auto_assign_compat to assign spans by device
registration order when backward compatibility needed.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
* Set it to 0 by default (as we use dahdi.auto_assign_spans now)
* Make it readonly (no runtime changes)
* Warn during startup if it was forced to 1
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Instead, use the inverse of dahdi.auto_assign_spans value.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Allow certain older firmwares to delay the hard reset until a full power cycle.
This way we can "preload" newer firmware images, without requiring the user to
physically power off/on their machine.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
This makes the behavior of IRQ misses for these drivers behave the same as the
wcte12xp, wctdm24xxp, and wct4xxp drivers.
Previously irqmisses would never increase. The presence of underruns would still
show up in dmesg as latency bumps.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
These were left over from when the VPM callbacks depended on the different VPM
installed. On the wcte43x this is unnecessary.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
These were left over from when the VPM callbacks depended on the different VPM
installed. On the wcte43x this is unnecessary.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
This was a legacy compile time option that is no longer necessary with the new
series of cards.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
struct dahdi_device.devicetype was set incorrectly in both drivers. This caused
the vpm module to not show up after the device name when reading this field
from a spanstat.
Reported-by: Charles Moye <cmoye@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
This fixes potential kernel panic due to accessing invalid memory if passing
invalid local span number to 'spantype' attribute via sysfs.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
It was an oversight to prevent the wcte43x and wcte13xp drivers from using
Message Signaled interrupts during the switch to the wcxb library.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
wcte13xp now has a max_latency module parameter like the wcaxx and wcte43x
drivers.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
The wcxb library did not do actually use the max_latency member to limit the
maximum latency of the DMA engine.
Now it does.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
The infrastructure has been put in place in 2.8.0 for fully dynamic device and
span configuration. This will be the default mode in DAHDI-Linux 2.9.0.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Oron Peled <oron.peled@xorcom.com>
Previously this was in __dahdi_init_span(). The problem was that
__dahdi_init_span() was only called when a spans' line mode was being changed.
Therefore it was possible to unassign and resassign an analog span and leave it
stuck in the 'NOP' alarm state.
It also make the setting / clearing of DAHDI_ALARM_NOTOPEN symetrical about span
unassignment / assignment in addition to updating the alarm states on all the
channels on the span via the dahdi_alarm_notify() function.
This is a better version of commit 496f817773.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This fixes an issue that affects TDM410 modules when there is not a module
installed in the first port, but there is an FXO module installed in the third
port.
When scaning for QRV modules in the first port, the 3rd port will have the
'hook' struct.qrv set to 0xff. When a QRV module is not detected, that value
will be left, which then maps to an invalid state for both fxo.ring_state and
fxo.battery_state.
The result would be that FXO ports would fail to run the ring detector state
machine since it did not know what the current state was.
Now we'll just reset all the values in struct fxo or struct fxs to the expected
init state.
Internal-Issue-ID: DAHLIN-332
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
A bug introduced in v2.8.0 prevented the recover timing configuration from
being set properly on the hardware. This caused the card to never go into
recovered timing mode.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
drv_attrs was fully removed from the bus structure in upstream commit
e18945b159a1cdbc031f1d3b0b7e515a33bdcbf7 which was merged into 3.13.
This is necessary to compile against linux kernel version 3.13.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
drv_attrs was fully removed from the bus structure in upstream commit
e18945b159a1cdbc031f1d3b0b7e515a33bdcbf7 which was merged into 3.13.
This is necessary to compile dahdi against linux version 3.13.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This resolves issues where, when using internal timing, the first channel of
span 3 has occassional corrupted data in transmit stream.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This extra read eliminates some problems with detecting certain S100M modules.
It is unclear at this time why it is necessary.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
The spi master cur_transfer and cur_msg should only be changed under the
spin_lock for the master. The result is that if running user space tools, like
fxstest, that check registers on the modules, it's possible to have a message
that was not yet complete flagged as completed which would result in a bad read.
This does not affect "normal" operation of the wcaxx driver since interrupts are
not enabled during module detection, and during normal operation all access to
the resgisters is done in the context of the interrupt handler. This would only
be an issue if the interrupt handler was running and register accesses are tried
in user space context on an SMP system.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
For the spans exported by the wctdm24xxp, the channels are not going to change
after they are already registered.
This eliminates a problem when analog spans are unassigned/reassigned and the
not_ready goes negative, thereby causing many warnings in the kernel.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Fixes the following warning when loading the driver:
dahdi: Warning: Span DYN/eth/eth1/00:50:c2:97:92:1d/1 didn't specify a spantype. Please fix driver!
The spantype is intended to be used by the auto configuration tools
(dahdi_genconf, pinned spans, etc..) but dynamic spans, since they are created
directly by dahdi_cfg, never take part in the pre-registration auto
configuration, therefore the span type was never used.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This change will ensure that the oct612x module is unloaded automatically when
/etc/init.d/dahdi stop is run.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
* This changeset adds master_span as an attribute of the span's driver:
/sys/bus/dahdi_spans/drivers/generic_lowlevel/master_span
* This is mainly used for debugging.
* Reading from it the master span number (or 0 if there is no master
span).
* Writing a number to it, force specified span to be master
* Existing Alternatives:
- grep "MASTER" from /proc/dahdi/*
- cat /sys/bus/dahdi_spans/devices/span-*/is_sync_master
(Note: commit d8fe2af23d is also Acked-By
Tzafrir Cohen <tzafrir.cohen@xorcom.com>)
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Rename as terminology has changed. No change in kernel interface.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
* No functional changes.
* Rename the span 'master' to 'master_span' to avoid ambiguity with the
'master' channel.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Create a "ddev" symlink from span's sysfs node to the one of its dahdi
device.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Send the new DAHDI_TOOLS_ROOTDIR and existing DAHDI_INIT_DIR with udev
device events as well.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
* Passed to udev as DAHDI_TOOLS_ROOTDIR environment variable
* Default is "/"
* Deprecates the parameter initdir:
- Defaults to $DAHDI_TOOLS_ROOTDIR/usr/share/dahdi
- If specified: taken relative to $DAHDI_TOOLS_ROOTDIR
- Setting both parameters explicitly is prohibited.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
If the driver is loaded with vpmsupport=0, then it was possible to create a
deadlock situation since the call into __dahdi_ec_chunk might then try to grab
the channel lock while already holding the reglock.
The purpose of grabbing reglock in the DMA routines was to protect the channel
array, which can be changed when linemode is changing. So instead, we'll
completely mask off that interrupt line from all CPUs when potentially changing
the channel array.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
The meta block contains specific version and checksum information and allows the
test tools to validate the image in the flash.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
From: Wendell Thompson <wthompson@digium.com>
These new cards are based on a common architecture with the TE133/TE134 as well
as the new analog cards, A4A/A4B/A8A/A8B.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
From: Rus Meyerriecks <rmeyerriecks@digium.com>
* Removed work queue for maint interface as it is not needed in this driver
* Error counters are now accessible through the maint interface
* Consolidated and revised the big maint switch case
* Added loopup/loopdown code transmit logic to E1
* Now supports error/defect insersion
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
From: Russ Meyerriecks <rmeyerriecks@digium.com>
The framer appears to continue transmitting a signal after modprobe -r. This
patch will leave the physical framer reset pin asserted to force the chip to
stop transmitting a signal when there is no driver attached.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
From: Russ Meyerriecks <rmeyerriecks@digium.com>
Removed all the custom logic and replaced with the common platform wcxb stuff.
There are also changes in here to standardize the function prefix in this
driver to t13x_.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
From: Wendell Thompson <wthompson@digium.com>
Now uses framer interrupt vector polling (in the FPGA interrupt) for
alarm, loopcode, and signaling events eliminating continuous polling.
Now uses timer function for alarm and loopcode debouce, which only
executes during exception conditions.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This is a driver for the new line of analog cards that shares a common interface
with the TE133/TE134 and the TE435.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
The octasic library is relatively large and is currently separately linked into
both the wcte13xp and wct4xxp libraries. This change moves it out into a
separate loadable module.
The bigest change from the drivers perspectives is that they must provide a
table of callbacks instead of using statically linked Oct6100UserXxxxx functions
to allow the library to communicate with actual parts on the cards.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This works around some issues with older versions of the firmware not
working properly after the linemode is changed via sysfs. Basically the
intent is to simulate redoing a complete driver reload with a new
linemode.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This print happened when the linemode was changed via sysfs, but it didn't
really add much extra information that a user could act on.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
dahdi_genconf currently does not take into account the number of spans
configured for a particular board. Therefore if you have two dual span cards
installed in the system, it could be possible to have something like this in
/etc/dahdi/system.conf:
spans=1,1,...
spans=2,2,...
spans=3,3,...
spans=4,4,...
When what you really want is something like this:
spans=1,1,...
spans=2,2,...
spans=3,1,...
spans=4,2,...
Otherwise, spans 3 and 4 will be configured to not recover the clock from the
span which is most likely NOT what you want.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This eliminates the need for board drivers to always re-report their alarm
states when spans are unassigned and then reassigned.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
The driver assumes that the first slot is not empty. If this is not the
case, synchronization will not work.
Fail loading if this assertion does not hold.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Astribank 2.02: a newer model: slight variation of 2.01 (both use E-Main
4). Uses the same USB firmware, has to use a different FPGA firmware as
newer devices cannot be made to work with older 2.01 firmware.
FPGA rev. 11307.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
* Our user-space previously used the implicit location from the sysfs
device path of the "dahdi_device".
* However:
- Sysfs paths are very limited in length.
- Low-level driver need more control on the location field.
- For example, it need to be persistant for span_assignments.
* We now export explicitly the 'location' field which is managed by
low-level drivers.
* We will use this field as the location in span_assignments.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
init_card_1_30 (FXS modules init script) can now use the new sysfs
interface to set ring settings.
Currently it only overwrite a single register
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
A new SysFS interface for FXS modules (XPDs):
* In /sys/bus/xpds/devices/<ll>:<m>:<n>/fxs_ring_registers
* Reading show current register values for NEON/TRAPEZ/NORMAL
* Modify the table via writing: "<column> <reg> <byte> [<byte>]"
* Example:
echo "NEON 0x33 0x12" > \
'/sys/bus/xpds/devices/00:0:0/fxs_ring_registers'
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
xpp: refactor the FXS module ring settings into separate data structure:
* Update High VBAT initialization in init_card_1_30:
- Take the value used in set_vm_led_mode() (0x34)
- Now we don't need to set it over and over again in set_vm_led_mode()
* Create a unified ring_parameters[] array for all ring registers:
- Columns for 3 ring types (NEON, TRAPEZ, NORMAL)
- Used by new send_ring_parameters() function
* Now the set_vm_led_mode() simply calls send_ring_parameters()
* This cleanup would allow us to change ring parameters at runtime (by
updating the values in these tables).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
With certain pci controllers that support pci hotplug, during the reset
sequence of the fpga, the host controller can get confused about the state of
the card and throw an nmi.
Known affected systems:
HP proliant DL160 & DL360p
Dell poweredge R520
Super Micro X7SPA-HF
This patch attempts to work around that by removing the fpga reset sequence
from the driver startup, then setting various control registers to known
starting state values.
This patch removes the field upgradeable firmware logic temporarily for the
te133 card to prevent fpga reset.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
* If userspace would run
modprobe xpp_usb && cat /sys/bus/astribanks/devices/xbus-00/waitfor_xpds
it would return immediately rather than wait for the Astribank to
initialize.
* We sometimes managed to read before getting the reply from the
astribank.
* Now we don't trust unit count at such an early stage.
* Instread we wait for the Astribank to reach a stable state (READY or FAIL)
before finish waiting for this astribank.
Internal-Issue-ID: Xorcom-1502
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
* In old kernels (e.g: 2.6.18) sysfs file names must be shorter
then KOBJ_NAME_LEN.
* Longer names are truncated and this leads to duplicate names
which fails device_register()
Examples: "dahdi!channels!10!10" is truncated to "dahdi!channels!10!1"
* The fix shorten the names and make them fixed length. Example:
"dahdi!chan!010!010"
* It seems no current userspace tools rely on that name or on
/dev/dahdi/channels .
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
This was causing inconsistancies with dahdi_scan showing an "UNCONFIGURED" span
in the "RED" state.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
