Previous commit (r10649) included an incorrect version. Including full message
from that commit for the description.
rev. 10502 of the FPGA firmware for the new E-Main rev. 4 fixes a potential
issue when used on Xorcom XR1000 systems: an issue with the power supply may
cause the unit to reset.
Note that there is no issue with previous models, with a normal setup of an
Astribank, or other XRx000 systems.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10652 a0bf4364-ded3-4de4-8d8a-66a801d63aff
rev. 10502 of the FPGA firmware for the new E-Main rev. 4 fixes a potential
issue when used on Xorcom XR1000 systems: an issue with the power supply may
cause the unit to reset.
Note that there is no issue with previous models, with a normal setup of an
Astribank, or other XRx000 systems.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10649 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Print a warning message that it may be a GPL violation to redistribute these
binaries if the firmware for the VPMOCT032/64/128/256 is compiled in.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10646 a0bf4364-ded3-4de4-8d8a-66a801d63aff
It appears that some kernel configurations do not include timer.h in any of
the include files that are included by dahdi_dummy. The timer_structs are
defined in timer.h and not time.h, so this change is correct even though I
never could find a configuation myself that actually failed to compile.
This has negligible impact since dahdi_dummy is not compiled by default.
Internal-Issue-ID: DAHLIN-185
Reported-by: Steve Murphy
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10640 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'irq' field was removed from dahdi_span in r10276 "dahdi: Remove
dahdi_span.irq and move dahdi_span.irqmisses into dahdi_device." [1]
which was first released in dahdi-linux 2.6.0.
[1] http://svnview.digium.com/svn/dahdi?view=revision&revision=10276
Reported-by: Pavel Selivanov
Internal-Issue-ID: DAHLIN-278
Patches: hdlc.patch by Pavel Selivanov (license #5420)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10634 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes a crash on unload if the sync_tick callback was running at the same time
the dynamic local span was destroyed. It was possible for
dahdi_dynamic_local_transmit to dereference a pointer that may have already
been freed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10627 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Minor change to follow generally recommended practice. Prevents new packets
from being queued up for devices when they are about to be cleaned up. Also
clean up any skbs that may still be on the queue after unloading.
Also closes anoter potential kernel oops on module unload. It was possible to
delete the private structure while the master span process was running. The
result was an attempt to page memory from interrupt context.
Make sure that the pvt function is set and cleared under the zlock. Also do
not assume that the pvt pointer is valid in ztdeth_transmit.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10626 a0bf4364-ded3-4de4-8d8a-66a801d63aff
I saw a kernel oops that was the result of the timer running after the
dahdi_dynamic module was unloaded. Now we wait for the timer to complete, and
then delete it again in case it reactivated itself.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10625 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The board drivers are the ones calling the unregister function, and
therefore we do not need to worry about them unloading while calling the
destroy callback.
When destroying spans with the ioctl, replace __module_get() with
try_module_get. This avoids hitting a BUG in module_get on kernel versions <
2.6.29.
ALSO move the call to try_module_get out of the dahdi_dynamic_release function
and into destroy. This way if the destroy callback isn't called because the
dynamic driver is unloading the dynamic device can be left on the list to be
cleaned up by the dahdi_dynamic_unregister_driver function().
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10624 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Instead of registering a function pointer, register a dahdi_dynamic_ops
structure that contains the owner as well as the ioctl callback. This way
dahdi.ko can bump up the reference count on dahdi_dynamic.ko before calling
the ioctl callback.
Also, use the registration mutex to guard against the module being unloaded
between the time the structure pointer was checked, and the module reference
is taken.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10623 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Enables the driver to update firmware on systems that do not have the firmware
loader configured / enabled (Linux config option CONFIG_FW_LOADER). Compiling
the firmware into the driver increase the memory footprint by around ~440K.
Internal-Issue-ID: DAHDI-963
Reported-and-Tested-by: Guenther Kelleter
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10618 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Newer versions of kernel build system do not require these Makefiles and
support for kernels older than 2.6.9 are no longer supported by DAHDI.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10617 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Quiet some checkpatch warnings introduced by the last patch. I kept this
separate since it may have obscured the real change made in the previous
commit if combined.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10590 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The driver makes the assumption that interrupts are disabled but this cannot
be guaranteed. We'll explicity disable interrupts on the local processor while
the interrupt handler is running.
This eliminates the "IRQF_DISABLED is not guaranteed on shared IRQs" warning
when loading the driver.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10589 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Resolves the follwing build error:
drivers/dahdi/dahdi_dynamic_eth.c: In function ‘ztdeth_exit’:
drivers/dahdi/dahdi_dynamic_eth.c:448: error: implicit declaration of function ‘cancel_work_sync’
RHEL kernel versions 2.6.18-238 (5.6) and greater had cancel_work_sync()
backported which is what I did my original smoke test on.
Reported-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10588 a0bf4364-ded3-4de4-8d8a-66a801d63aff
It was possible after a dynamic ethernet span was created for a packet to come
in before the dahdi_span was fully initialized. The result would be a NULL
pointer dereference. Now just discard any packets that might come in during
this time window.
Internal-Issue-ID: DAHLIN-280
Reported-by: Pavel Selivanov
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10587 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Adds a new parameter, 'lower_ringing_noise', to module xpd_fxs.
* Makes the "power-down" behaviour that was added
in upstream svn r10478, switchable in runtime.
* By default (false), makes the vbat_h behave like it did
before the power-down change.
- I.e: vbat_h is held throughout the ringing period (during
both ring-up/ring-down)
- So this patch revert part of r10478
* When switched to true, activate the "power-down" behaviour.
- I.e: vbat_h follows the ring-up/ring-down.
- This behaviour lowers the noise caused by group ringing of
FXS channels in the same unit, but causes problems with CallerID.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10574 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* In do_chan_power() make vbat_h changes atomic.
* As a result we can ignore duplicate requests.
This will allow cleaner logic in the next commit.
* Added proper debug messages.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10573 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This in conjunction with r10449 "A parent-less device should not crash dahdi",
this allows dahdi_dynamic spans to work post the dahdi_devices changes in
2.6.0.
The full address of the device is not used since kernels prior to 2.6.31 limit
the length of a devicename to 20 characters. The full address of the device
can be pulled out of the "hardware_id" and "type" fields of the span.
This patch is just to get things working again. dahdi_dynamic devices *may*
still have issues if the auto_assign_spans module parameter is 0.
Internal-Issue-ID: DAHLIN-280
Reported-by: Pavel Selivanov
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10563 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The masterspan can be, and often is, called with interrupts disabled but
dev_queue_xmit() needs to be called with interrupts enabled. This potentially
fixes a deadlock.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10562 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is needed because dev_name() is mapped to kobject_name() in a backport,
but the kobject name isn't set until after device_add(). The result would be
parentless devices would fail since dahdi would not think a name was set for
these devices.
For these systems, we'll set both the bus_id string and the underlying
kobject_name.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10561 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In addition to updating the year, this also adds some boilerplate to
dahdi-sysfs.c and dahdi-sysfs-chan.c that wasn't there previously.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10560 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is a partial revert of r10234 "wct4xxp: __t4_framer_in and
__t4_framer_out speedups."
There were some platform + firmware version combinations that would fail to
properly configure the framer with the aforementioned speedups. The originally
reported sympton was that interrupts would fail to start and while
troubleshooting I also saw cases where one of the spans would stay in alarm
after starting. By adding in additional reads to the version register, the
overall process of writing / reading from the framer control registers is
slowed down which increases reliability.
This change does *not* affect the main path of TDM data which is DMAed
directly into buffers in host memory and are not read / written to / from
framer registers directly.
Reported-and-Tested-by: Vahan Yerkanian <vahan@arminco.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10559 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Certain BIOSes appear to enable ASPM even though it is not fully supported by
the platform. Also, since the PCIe links for TDM cards are always in use it
does not make sense to allow them to transition to the disabled state.
Just turn off power management on the PCIe links completely. For more
information see http://lwn.net/Articles/449448/.
Internal-Issue-ID: DAHLIN-283
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10558 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Certain BIOSes appear to enable ASPM even though it is not fully supported by
the platform. Also, since the PCIe links for TDM cards are always in use it
does not make sense to allow them to transition to the disabled state.
Just turn off power management on the PCIe links completely. For more
information see http://lwn.net/Articles/449448/.
Internal-Issue-ID: DAHLIN-283
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10557 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Will allow the ASPM (Active State Power Management) state to be disabled on
PCIe devices before kernel version 2.6.25.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10556 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Remove a mostly harmless 0x1A (^Z) at the end of the file. If you
add a NL after it, it breaks the firmware loading.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10550 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The Makefile changes needed to install the two new files.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10536 a0bf4364-ded3-4de4-8d8a-66a801d63aff
USB firmware (USB_FW.201.hex 10402) and FPGA firmware
(FPGA_1161.201.hex 10480) with support of the new E-Main 4 Astribank
mainboard.
(This was accidentally labeled as 'E-Main 3' in some previous commit
messages)
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10535 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes an issues with the 6FXS/2FXO module: if an extra FXS or FXO module
is added to a system with such a module, an excessive number of port
licenses was accidentally required (as if the 6FXS/2FXO module required
8FXS/8FXO licenses).
Internal-Issue-ID: #1371
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10534 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Even though dahdi_dummy is no longer built by default, the adoption of
dahdi_devices in 2.6 broke the ability to compile. This was not intended as
there are some packagers who still patch the Kbuild file to enable
dahdi_dummy.
Internal-Issue-ID: DAHLIN-274
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10486 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Upstream commit bd77c047 "module: struct module_ref should contains long
fields" changed the return of module_refcount from int to unsigned long. This
change eliminates a warning from the string format specifier.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10485 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Eliminates warnings that are a result of upstream commit 72db395ffa
"module_param: check that bool parameters really are bool."
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10484 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This removes the following warning:
Section mismatch in reference from the function init_module() to the function .exit.text:dahdi_sysfs_exit()
The function __init init_module() references a function __exit
dahdi_sysfs_exit(). This is often seen when error handling in the init
function uses functionality in the exit path. The fix is often to remove the
__exit annotation of dahdi_sysfs_exit() so it may be used outside an exit
section.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10483 a0bf4364-ded3-4de4-8d8a-66a801d63aff
DAHDI internal timing currently uses the "wall clock" to determine how much
time is passing for mixing and timers. When the wall time changes, like when
the system time is set via ntp or date, DAHDI currently will display a
"Detected time shift" message since it believes there is too much audio to
mix. There may also be audio problems if the wall time is shifting
occasionally due to slewing of the clock.
Now use a monotonic clock to determine how much real-time has passed for
timing purposes. This makes DAHDI insensitive to any changes in the wall time
on the system.
This only applies when using DAHDI's internal timer like when there are not
any telphony cards installed. There are still potential audio problems if the
platform is unable to accurately determine the passage of time.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10482 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Rotate the channels table in /proc/xpp/XBUS-*/XPD-*/fxs_info
- This way we don't overflow 80 columns
- Can also add more info items per-channel
* Linearize LED output for easier grep'ping
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10479 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Now every linefeed control command which is not RING'ing
powers-down the SLIC. This reduce audible noise when
several channels are ringing.
* Simplify code by removing redundant calls to do_chan_power()
before linefeed_control()
* Manage vbat_h state so we skip do_chan_power() calls when
there isn't a state change
* Export vbat_h state to /proc/.../fxs_info
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10478 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* If a DAHDI_AUDIO_NOTIFY is issued, offhook the channel
(added to BRI).
* If D-channel is closed, onhook all channels (added to PRI)
* If a clear channel is closed and the D-Channel is not
open (e.g: with patgen/pattest), onhook this channel
(added to both BRI and PRI)
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10476 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* A driver reload should reset Astribank hardware
* This patch send an SPI reset after we get AB_DESCRIPTION reply from Astribank
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10474 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In commit r10168 "wctdm24xxp: Use time interval for debouncing FXO ring
detect" [1], I inadvertently changed the debounce interval of the RINGOFF
event from 128ms to 512ms. The result was a potential failure to detect CID,
depending on line conditions, since Asterisk would bump the rx gains on the
channel in the middle of the CID spill as opposed to before the CID spill.
This fixes a regression first introduced in DAHDI-Linux 2.6.0.
[1] http://svnview.digium.com/svn/dahdi?view=revision&revision=10168
Internal-Issue-ID: DAHDI-951
Reported-and-Tested-by: Jack Wilson <ljwilson@digitalav.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10473 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This patch removes support for kernel versions < 2.6.18, as those are
not actively supported in any major Linux distribution (except RHEL4,
which is in the "extended" support level of the product life cycle).
This removes much of the more #ifdef-rich parts of the code.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10472 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Shortcut CLASS_DEV_CREATE/CLASS_DEV_DESTROY. No need to pass repetitive
data (and NULL) on every call.
* Create/remove fixed device files (ctl, timer, channel, pseudo) via
generic code (fixed_devfiles_create()/fixed_devfiles_remove()) instead
of repetitive code and flags.
* Try to make all removal/cleanup functions idempotent, so we can
safely call them on any failure without the need for multiple goto
destinations.
* Rename 'device_state_flags' to 'should_cleanup' and its member
flags to a better/consistent naming.
* Rename dahdi_sysfs_exit() to dahdi_sysfs_cleanup() and call it from
a new proper dahdi_sysfs_exit()
* In dahdi_sysfs_init(), handle dahdi_sysfs_chan_init() failures
* Add dahdi_dbg() message before creating/removing all DEVICES
objects.
* Also move two KERN_INFO messages to a more correct locations:
- The version reporting should be first (in dahdi-base.c)
- The "Telephony... on major" reporting should be at the end
of dahdi_sysfs_init()
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10464 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Move sysfs class and device files management into dahdi-sysfs-chan.c
* This does not change functionality, just a preparation for later
code cleanups and improvements.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10463 a0bf4364-ded3-4de4-8d8a-66a801d63aff
