This fixes an issue where "EC: LASVEGAS2" was displayed in /proc/dahdi/x
for a B410P span even though vpmsupport was disabled with the module
parameter.
Internal-Issue-ID: DAHLIN-247
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10251 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Allows the globalconfig member to be removed from the struct t4 and not
carried around for the life of the card. Also holds the reglock a little
longer for all the framer writes but I realize the startup of the
wct4xxp based cards does not need to be optimized.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10250 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Reduces the amount of code to read in the two functions and fixes
checkpatch.pl warnings.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10249 a0bf4364-ded3-4de4-8d8a-66a801d63aff
There are read/modify/write operations on the framer that were not
protected by any locks. While I didn't notice any code paths that would
result in simultaneous accesses to these registers, this change will
hopefully save someone else some time in the future verifying that the
accesses are safe. A side effect is that the reglock is acquired only
once for each read/modify/write cycle as opposed to twice previously.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10248 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since 'linemode' more accurately describes what spantype is specifying.
We can also use an enumeration for the linemode to make it explicit that
linemode is only set to one of three possible values.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10246 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Use some convenience pointers to make the function easier to read as opposed
to indexing into the arrays.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10245 a0bf4364-ded3-4de4-8d8a-66a801d63aff
All those checks for wc->t1e1 span appear to basically be there to
determine if there are *any* E1 spans exported by the card. We can make
that explicit by wrapping those tests with a has_e1_span() inline
function to help with readability.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10244 a0bf4364-ded3-4de4-8d8a-66a801d63aff
't1e1override' isn't immediately apparent what it is supposed to do by the
name. Instead 'default_linemode' module parameter can be set to "auto", "t1",
or "e1" to make it clear.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10243 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since removal of the VPM400 support the 'vpm' member of struct t4 is
now redundant with the 'vpm450m' member.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10242 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The VPM400 module is no longer supported by the wct4xxp driver. The
VPMOCT064 and VPMOCT128 are.
Signed-off-by: Russ Meyerreicks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10241 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Saves about a 1us on average from the interrupt handler on one test
system.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10239 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Eliminates the need to store a copy of the flags and variety from the
global devtype.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10238 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'memaddr' and 'memlen' is already cached as part of the underlying pci
device so the wct4xxp driver does not need to cache it again. 'canary',
'passno', 'master', and 'oct_rw_count' are unused.
In t4_span 'irqmisses' was incremented, but never used anywhere, and there is
already the irqmisses on the span itself.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10237 a0bf4364-ded3-4de4-8d8a-66a801d63aff
I was unable to measure a performance change with prefetching.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10236 a0bf4364-ded3-4de4-8d8a-66a801d63aff
We are already in hardirq context and can therefore save the cli/sti
call.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10235 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Speeds up these calls primarily by eliminating unnecessary flushes
of writes to the PCI bus.
Before:
7.095 us | __t4_framer_in();
5.835 us | __t4_framer_out();
7.122 us | __t4_framer_in();
7.071 us | __t4_framer_in();
7.059 us | __t4_framer_in();
5.859 us | __t4_framer_out();
7.076 us | __t4_framer_in();
5.852 us | __t4_framer_out();
7.124 us | __t4_framer_in();
7.080 us | __t4_framer_in();
After:
1.694 us | __t4_framer_out();
1.686 us | __t4_framer_out();
1.695 us | __t4_framer_out();
3.182 us | __t4_framer_in();
3.283 us | __t4_framer_in();
2.889 us | __t4_framer_in();
2.942 us | __t4_framer_in();
2.951 us | __t4_framer_in();
2.906 us | __t4_framer_in();
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10234 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The 'pedanticpci' module parameter, which is always on by default,
inserts extra reads from the card in order to ensure that all writes are
properly flushed through any PCI bridges which may post the writes. The
side effect is that this takes more CPU time for registers reads and
writes, especially to the framer registers.
It is never recommended to run with pedanticpci set to 0, so I'm
removing it as a module parameter so that the default case does not take
a performance hit checking for whether the parameter is set or not.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10233 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Also has the nice side effect of eliminating a comparison from the
interrupt handler.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10232 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The overhead of reading the framer registers is significant and can
result in latency bumps / data drops on heavily loaded systems.
Instead of checking all spans every millisecond when they are in
alarm we will instead only check every 100 ms.
On one test system, dropped the % CPU time spent in hard interrupt
context from 10% per TDM4XX when all four spans are in alarm to
closer to 2%.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10231 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is the "normal" condition and can be lumped with the other
informational messages. Otherwise, just this one message might go to the
console depending on the system configuration which can be confusing.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10230 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This value is not used and is now gone.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10229 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r10160 "wctdm24xxp: Probe for and configure modules in parallel."
did not properly setup the VPMADT032 for all ports on hybrid cards.
The most immediate sympton being that spans 3 and up on a hybrid
card would not come up in Asterisk even though they were out of
alarm. This was because the echo canceler was blocking messages on
the dchannels.
This does not affect any previously released versions of DAHDI-Linux
or users of the VPMOCT032.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10228 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Uses the linecompat member to determine what type of span it is. This will
allow removing T1/E1 flags from other places where the span type is stored.
This function also changes the return value from bool to int for the
inlines defined in include/dahdi/kernel.h. This is because not all
kernel versions include stdbool.h in the headers and it will conflict
with boolean values that are exported via module parameters on some
older kernels if dahdi included it globally.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10227 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Commit r9750 "wct4xxp: Reduce the memory footprint of the hardware
echocanceler.", as part of reducing the non-pageable memory required to
support the VPMOCT064 and VPMOCT128, disabled caching of some hardware
echocan registers. This resulted in more physical reads to the echo
canceler. These new read transactions exposed an existing issue where
sometimes reads could be turned into writes which put a channel into an
unintended state preventing Asterisk from detecting any DTMF.
This issue is resolved by ensuring that the write signal to the Octasic
part is explicitly cleared between when the address is presented on the
bus and when the read and chip select signals are asserted. The cost is
an increase in the average time to enable / disable echo cancellation by
about 5 us on one Intel Xeon X3220 test machine (~250ns increase per
read from the Octasic part and 20 reads to enable / disable a channel).
This commit resolves a behavioral regression first introduced in 2.5.0
and 2.4.1 which could take many calls before revealing itself. This
change only affects cards with a VPMOCT128 or VPMOCT064 installed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Doug Bailey <dbailey@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10220 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The driver has, until now, dropped G723 SID frames even though the
firmware on the TC400/TCE400 can handle them. Now let them on
through.
Reported-and-Tested-by: Angel Carhuas <acarhuas@colinanet.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10218 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The intent here is to flag to users that the maintenance counters are
not collected for spans exported by the wcte12xp driver.
dahdi_maint before this change:
# dahdi_maint -s 1
Span 1:
>Framing Errors : 0:
>CRC Errors : 0:
>Code Violations : 0:
>E-bit Count : 0:
>General Errored Seconds : 0:
And after:
# dahdi_maint -s 1
Span 1:
>Framing Errors : -1:
>CRC Errors : -1:
>Code Violations : -1:
>E-bit Count : -1:
>General Errored Seconds : -1:
This can be combined with a change to dahdi_maint to recognize that the
errors are -1 and print an even more explicit warning.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10212 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Currently, the devicetype string was set both when the device was first
allocated and updated when an echocanceler was detected. For simplicity,
combine both these steps into a single function.
This change also replaces an improper use of strncat with strlcat.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10210 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* 'D' DTMF digits were accidentally discarded with the notice message:
"Bad DTMF value 0. Ignored".
* No need for an odd 1-based translation table anymore - it's 0-based.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10209 a0bf4364-ded3-4de4-8d8a-66a801d63aff
There were a couple of reports that MeetMe conferences were not
working in 2.5.0.1 and that downgrading to 2.4.1.2 resolved the
issue. This could occur if there were no analog spans in a system,
and all the digital spans were out of alarm before DAHDI_STARTUP
ioctl was called by dahdi_cfg. If the spans were *not* out of alarm,
they would be marked master when the span changes it's alarm state.
This would result in a condition where no spans were marked as the
"master" and so the core timer was handling conferencing. The core
timer runs by default at 4ms and most board drivers run at 1ms
intervals, but a channel currently only buffers up 2ms of data when
conferenced. Therefore, 2ms of audio from a board was continuously
dropped from the conference every 4ms by default.
This fixes a regression first introduced in 2.5.0 which was
specifically added in revision r9611 "dahdi: Do not locate new
master in interrupt context."
Internal-reference-ID: DAHDI-894
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Tested-by: Dennis Martinez <dmartinez@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10205 a0bf4364-ded3-4de4-8d8a-66a801d63aff
These members are not used anywhere and are now gone.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10204 a0bf4364-ded3-4de4-8d8a-66a801d63aff
A "(VPMADT032)" string is appended to the devicetype (as shown by
dahdi_scan) for the span if one is installed. Now append '(VPMOCT032)'
if one is installed as well.
Also, for the wcte12xp driver append the VPM name to the device type after
initially probing as opposed to only after the span is configured.
(Related to issue DAHDI-890)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10203 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Bug sympthoms: wrong FSK VMWI sent few seconds after
offhook. That was caused because the driver kept
polling the (physically unconnected) digital inputs.
[note: a workaround for drivers without this patch
is to zero the 'xpd_fxs.poll_digital_inputs' parameter.]
* Also, the digital_inputs/digital_output masks were
calculate using a different condition.
* Now we determine number of channels, digital inputs and
digital outputs in a single place and use this info
later to calculate the correct masks.
* We poll only if there are digital_inputs
* We added a sanity check in process_digital_inputs, so
we get a notice if it's called on an xpd without digital
inputs (e.g: hypothetic firmware bug).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10202 a0bf4364-ded3-4de4-8d8a-66a801d63aff
DAHDI currently waits a second before checking if a board driver is
calling dahdi_receive and switching to internal timing. Some versions of
Asterisk (I was looking at 1.4.42 when writing this) only wait 300ms for
a timer to expire when first starting and verifying that DAHDI is
properly configured. This can result in a
"ERROR[27673] asterisk.c: Asterisk has detected a problem with your DAHDI
configuration and will shutdown for your protection. You have options:"
message if asterisk is started soon after loading DAHDI.
This change sets the inital polling interval to the same as that used
during normal coretimer operation, 4ms. The interval will still be
slowed to 1 second if a board driver starts calling dahdi_receive().
DAHDI-892.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10200 a0bf4364-ded3-4de4-8d8a-66a801d63aff
New firmwares to handle the new 2FXS/6FXO module.
FPGA_1161.hex, PIC_TYPE_1.hex, PIC_TYPE_2.hex of internal rev. 9732
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10179 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Firmware version 1.11.0 resolves an issue where the driver fails to
detect certain VPMOCT032 modules after a cold boot.
Signed-off-by: Doug Bailey <dbailey@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10172 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The driver / FXO modules now always operate in a fwringdetect mode and the
module parameter was never checked anywhere. It is now gone.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10171 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Eliminate the assumption that the check function is going to be called
for every frame. Also use a state machine to make polarity debouncing
similar to the other debouncing code.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10170 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Allows the driver the option of not calling the misc function for every
frame. This is part of preparation for moving misc processing out of
the interrupt handler. Also use a state machine for the various battery
states to unify the technique for debouncing the various signals in the
driver.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10169 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Do not assume the ring detection function is called for every frame.
Also change the debounce logic to a state machine to clarify what state
a port is in and unify the technique for debouncing the various signals.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10168 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Part of moving more of the module specific processing out of the
interrupt handler and allowing the interrupt rate to be slowed down.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10167 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Part of preparations for being able to optionally slow the interrupt
rate down and opening the door for moving more module processing out of
the interrupt handler.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10166 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Saved me time when reading the code so I don't have to lookup which position
in the index is what register for each of the modules.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10165 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The variable does not necessarily have anything to do with the frequency
of interrupts but is instead a count of sframes received. For example,
it is possible to slow the interrupt rate down on the voicebus cards to
one every 2 frames.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10164 a0bf4364-ded3-4de4-8d8a-66a801d63aff
We can spend less time in interrupt context by not saving and restoring the
local interrupt state. This is a particularly noticeable improvement on debug
kernels with lockdep.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10163 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Closes a small window of opportunity where one CPU might free a VPM
instance that the interrupt handler may currently be using.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10162 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Wait until we have de-bounced the presence of battery before moving on the
check for changes in polarity. This removes the sometimes random
polarity messages generated on an FXO port when the far side drops
battery from a supervisor disconnect.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10161 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Use the newly create bg_create and bg_join to actually probe / configure
groups of 4 modules in parallel. This currently has to be done in groups
of four due to the way 4-port modules are identified relative to single
port modules.
This provides a dramatic improvement in driver load time. When loading a
single TDM2400 with 24 FXS ports before this change:
# time modprobe wctdm24xxp vpmsupport=0
real 0m46.674s
user 0m0.000s
sys 0m0.520s
And after this change:
# time modprobe wctdm24xxp vpmsupport=0
real 0m7.900s
user 0m0.000s
sys 0m0.070s
Note that the boards themselves are still configured serially. Board
configuration can be parallelized once the assignment of board position
is moved out of the function that is run in parallel. Otherwise it could
be possible for board numbers to switch on repeated loads.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10160 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Create a generic facility to spawn tasks to run in parallel. There are
interfaces already in the kernel for doing this, but they are not
supported on the full range of kernels that DAHDI must support.
This will be used to identify and configure FXS/FXO/B400M/VPM modules in
parallel.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10159 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When the driver begins to initialize a device it conducts a read/write
test on one of the framer registers. The driver ignores the result of
that test and results in much output spammed to the kernel logs for a
failed card since the driver doesn't then try to unbind from the device.
What was getting spammed:
wcte12xp 0000:03:01.0: Timeout in t1_getreg
wcte12xp 0000:03:01.0: Wrote '0' but read 'fffffffb'
Now abort the bind if the read / write test fails.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10155 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r10006 "wctdm24xxp: Add 'fastpick' module parameter." copied the
fast-off hook module parameter from the wctdm.c driver, but the setting
in that driver does not match the data sheet. The previous commit did
not actually change any of the significant bits in that register. Also,
that commit changed the timer, but did not disable the callibration
delay which is necessary for Type-II callerid.
The fastpickup option in the wctdm24xxp driver should now match the
fastpickup option in the wctdm driver.
DAHDI-224.
Reported-By: Kinnith Wallace <kwallace@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10148 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Really only *necessary* when SLAB debugging is enabled, but in that
case, can reduce the chance of latency bumps when first loading the
driver. Otherwise the constant slab poisoning / checking in interrupt
context from the kmalloc / kfrees is too much.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10144 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The logic loops through the static cards[] array to determine timing,
but the subloop was based off the current card's numspans member.
This could cause a null dereference in the case where two cards of
different span densities were connected via timing cables.
Reported-by: Doug Bailey <dbailey@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10140 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r10082 "wctc4xxp: Cleanup in-flight commands when halting due to
hardware error." introduced a lock imblance on the error path where the
cmd_list_lock would be unlocked twice when the board is halted due to a
hardware error. Thanks sparse.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10138 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r10066 "wctdm24xxp, wcte12xp: Run the ISR with interrupts disabled."
requested that the interrupt handler be run in "fast" mode (disabled)
but this isn't necessarily guaranteed.
This patch makes the interrupt handler itself disable all the interrupts.
Linux commit 470c66239ef0336429b35345f3f615d47341e13b [1] contains a comment
about why this is necessary.
[1] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=470c66239ef03364
(closes issue DAHLIN-248)
Reported-and-Tested-by: Vladimir Mikhelson <vlad@mikhelson.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10118 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Currently dahdi_receive is called on all channels in the context of the
master dynamic span. If one span (not the master) receive two packets
before the master span received a packet, the older packet on the
dynamic span would end up lost because the "readchunk" for the
channels would be overwritten by the new packet. DAHLIN-245
Signed-off-by: Wagner Gegler <wagner@aligera.com.br> (License #6268)
Changed dahdi_ec_chunk to dahdi_ec_span.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10110 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Astribank II FPGA firmware rev 9605. Includes two bug fixes:
* Error in checking EC licenses when the license was for exactly 64 or 128
channels.
* Proper handling of a slave FXO Astribank (in line with the quirks
handling from r10019).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10099 a0bf4364-ded3-4de4-8d8a-66a801d63aff
DAHDI currently supports kernels >= 2.6.9. netdev_priv() has been in the
mainline kernel since versions 2.6.6 so it's available in all the
supported kernels. This change is needed to compile against the 3.1 kernel.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10096 a0bf4364-ded3-4de4-8d8a-66a801d63aff
On one system I was seeing the board reset in the middle of a
transaction. Any commands that were on the response list when this would
happen would never be completed and the process would then be stuck in
an uninterruptible sleep. This change also prevents the driver from
sleeping in timer context, which would result in a kernel panic.
This change at least lets an error message propogate back to the user.
DAHDI-880
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10082 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In the rare case where spanconfig is called while there is pending data
on the hdlc channel, the hdlc_getbuf interrupt could try to read from
the hdlc buffer before the channel was fully setup. This could
potentially result in a null pointer dereference. This condition has
existed since the creation of the wcb4xxp driver.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10079 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When attaching software echocans to a channel, if there is a hardware
echocan available always give preference to them.
Revision 9995 "dahdi: Always attach hwec to a channel if available" had
an error where if a driver did not even support an option of hardware
echocan, dahdi-base would take that to mean there always was a hardware
echocan available on the channel.
DAHLIN-246
Reported-by: Michael L. Young
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10070 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Revision 9886, "wcte12xp: Use the in-hardirq versions of
dahdi_receive/dahdi_transmit", changed the call into dahdi_receive and
dahdi_transmit to use versions that assume local interrupts are already
disabled. Not all versions of the kernel run interrupt service routines with
all interrupts disabled and therefore it was possible to lock up a CPU with a
recursive grab of the chan_lock.
When LOCKDEP was enabled (on debug kernels) interrupt handlers were run
atomically so this problem would only occur on pre 2.6.35 kernels that did not
have lockdep enabled.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10066 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The wcte12xp wasn't recognizing loopup/loopdown signals. The debounce was so
long that it was preventing the loopup/loopdown signals from being registered
properly. Removed the debounce entirely as it was unnecessary to the operation.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10064 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Revision 9750 "wct4xxp: Reduce the memory footprint of the hardware
echocanceler" reduced the number of bits used to store some structure
members. Some of the new field lengths were unable to store all the
possible values the API as used assigned to the fields, resulting in
channels never entering power down mode when they were disabled like
they were previously.
The change for byEchoOperationMode was found in testing the operation of
the VPMOCT032 which currently uses the same code. The others were done
via a review of the API doc.
This change represents negligable risk and contains no logic changes.
It only increases the memory footprint of the API instance in the
kernel.
Signed-off-by: Doug Bailey <dbailey@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10060 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Make sure that the call to dahdi_chan_unreg() in free_pseudo() is
protected by the registration_mutex, like the other calls to that
function.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-By: Oron Peled <oron.peled@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10056 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Required by CAS in latest (2.5) DAHDI versions.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10055 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This avoids a nag about a meaningless single-bit signed int.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10054 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If the CPU becomes overly busy, merely printing the "Overflow in the
recieve_queue" messages becomes CPU-intensive on its own right.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10052 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The shutdown logic requires that all CPUs see that the INITIALIZED bit
has been cleared. Otherwise it may be possible for the workqueue to run
after the hardware resources have been released.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10047 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If the OCT6104E-256D.ima Octasic firmware was downloaded to the build
directory, install it over with the rest of the firmware files.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10038 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If set to true (default) a HWEC, if available on the channel, takes
priority over any software echocan configured in /etc/dahdi/system.conf.
This has historically been the default behavior in all released versions
of DAHDI that support module echocans.
Otherwise, hwec_overrides_swec is set to false, HWEC is chosen only via
the "echocanceller=hwec" directive.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-By: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10036 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This adds module parameter 'ring_trapez'. When set, the wave form of
the ring tone is set to be a trapezoid, rather than sine. Thus making
the ring stronger.
This is a boolean parameter of the module xpd_fxs. Takes effect at the
beginning of the next ring.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10022 a0bf4364-ded3-4de4-8d8a-66a801d63aff
gcc 4.6 complains about variables that are assigned values but then
never used.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10020 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In some cases the hardware echo canceller cannot be used. Mostly related to
an FXO module.
* FXO module if the first module is BRI or PRI
* FXS module if the Astribank has another FXO, no PRI/BRI, and is a sync
slave.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10019 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r9943 enabled the presence of hardware EC to be probed on a card. That
change did not account for wcb4xxp based cards that did not have a
hardware echocan on board.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10017 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The dual and quad span cards have a rotary switch onboard which controls
the order that cards serviced by this driver are registered with the
core of DAHDI. This commit adds a module parameter 'ignore_rotary'
which, when set to 1, causes the driver to ignore the position of the
rotary switch and only consider the physical slot when registering with
DAHDI.
Ignoring the rotary switch settings also permits the PCI device to be
bound and unbound from the driver at runtime since registration with
DAHDI no longer only happens when the module is first initialized.
By default, the rotary switch will still be used to determine
registration order. This commit does not change the default behavior.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10016 a0bf4364-ded3-4de4-8d8a-66a801d63aff
New Astribank II FPGA firmware and USB firmwares that add support for the
hardware echo canceller module.
Note that due to a bug in previous FPGA firmwares, an Astribank with such
older firmware and with a hardware echo canceller module will not have any
functioning audio at all.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10013 a0bf4364-ded3-4de4-8d8a-66a801d63aff
I failed to compile the commit exactly as it was committed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10008 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When true / 1 the FXO port will use a shorter off-hook calibration
delay. This is sometimes necessary in order to properly decode Type-II
Caller ID information which is sent shortly after an FXO port goes off
hook.
Defaults to 0 unless opermode is "JAPAN" then it will default to 1. This
functionality was ported from the wctdm.c driver.
DAHDI-854.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10006 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If an FXS port is configured to use kewl start signalling, when the FXS port
is "hungup" it should drop battery for 500ms so that any attached devices can
detect that the remote side has disconnected. The wctdm24xxp driver
since version 2.4.0 was only dropping battery for ~5-10 ms because it would
set "open" on the line, but then the next time it read the line feed register
state, it was setting the LINE feed register to the idle state.
This change checks if the line is forced open before setting the FXS port back
"onhook" so as to not turn on battery prematurely.
This fixes a regression introduced in r9070 "wctdm24xxp: Prevent FXS Proslic
staying in "Forward/Reverse OnHookTransfer...". DAHDI-849.
Checking for open on the line feed registered was originally suggested by Alec
Davis.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10002 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The firmware load has been moved into a workqueue to prevent the module load
from blocking for the duration of the firmware upload. This could be up to 40
seconds. Driver prevents configuration until firmware load is finished and
is_initialized() returns true.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9998 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Support enabled for the vpmoct032 echo cancellation module for the wctdm24xxp
and wcte12xp drivers.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9997 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In previous releases of DAHDI if dahdi_cfg attached a software echocan
to a channel and a hardware echocan was available, the hardware echocan
would be used instead of the software echocan.
Since the 2.4 branch was created a new feature was merged into
dahdi-linux where it was possible to mix software echocan and hardware
echocan on a channel. This required using "hwec" as the echocan in the
/etc/dahdi/system.conf file so that what was specified in the
configuration file is what was actually used.
This has resulted in users upgrading to the trunk of dahdi without
updating their /etc/dahdi/system.conf file and just suddenly not using
any hardware echocans any longer.
The capability to mix software and hardware echocans on a span will be
revisted when running dahdi_cfg on any preexisting configuration files
doesn't just silently turn off hardware echocan.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9995 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* xpd_echo (card_echo.c) - a module to handle an Astribank hardware echo
canceller module.
* All other XPDs are now of type 'telephony_device'. Only a telephony device
XPD provides a span to register.
* The EC module will typically show up as XPD-40 and will always show up as
Unregistered in 'dahdi_hardware -v'
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9993 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reverts commit r9891 and is part of two commits to revert all the
timer changes.
Grouping the timer into rates did not allow a timers rate to be changed
after another thread is already blocked on the poll call
The problem that was reported was if a sip call was made to a DAHDI
channel and the sip call was disconnected before answer, the DAHDI
channel would never stop rining.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9991 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reverts commit r9937 and is part of two commits to revert all the timer
changes.
Grouping the timer into rates did not allow a timers rate to be changed after
another thread is already blocked on the poll call
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9990 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r9946, "wcte12xp: Move the VPMADT032 test/configuration to module load
time." introduced a race condition where it was possible for the timer
that initiates the check for the alarms to fire before the board was
marked initialized. This would result in a board that would never again
check it's alarm state since the first time the timer runs INITIALIZED
may not be set and it will not reschedule a check since it believes the
driver is unloading.
This happened because the check for the VPM was moved between when the
timer was first setup and when INITIALIZED was then set.
Now we make sure INITIALIZED is set before the timer is first setup, and
move those two operations together.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9981 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In commit r9968 "wctdm24xxp: Allow more than one outstanding read at a
time" I introduced a regression where the transmit FIFO on the data
channel of a B400M could get locked up. The result would be constant
HDLC overflows when writing to the data channel.
This regression did not make it into any releases and did not exhibit
itself when crossing spans on a single B400M module. This is a partial
revert of commit r9968.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9977 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The board number dupliates the information that is available in the
location field. Exporting it as part of the description makes the name
dependent on the driver bind order which is not desirable.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9971 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Updates the CMD_BYTE macro to use precalculated offsets.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9970 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since every read needs to go through the complete voicebus pipeline, if
we know we're going to read multiple bytes we can queue them all up.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9968 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Saves time in the interrupt handler by eliminating the need to scan
through all of the slots in the cmd arrays. Also allows the reads from
ISR context to automatically grow as the latency grows. This ensures
that battery and hook state is actually checked every frame like
originally intended.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9966 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Trivial reformatting that preps it for some parallelizing the module
loads.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9965 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The card position is only used during startup so we don't need to carry it
around in the strucuture.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9964 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The voicebus cards only support the S110M FXS modules which are based on
the 3215. The module flags member was only used to hold whether we were
dealing with a 3210 or 3215 SLIC, so we can drop it since we always know
we'll have a 3215 based SLIC.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9963 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Cuts down on the overhead of constantly saving and restoring the
interrupt registers.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9962 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change gets all the easy places and saves on array dereferences
when we already have the address of the module that we are interested
in.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9961 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change is to primarily to clarify that the types are always mutually
exclusive.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9958 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This also allows us to add them to the union with the other module types so
they do not add to the memory usage if there aren't any QRV modules installed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9957 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Move the data backing the mostly unused string away from the active
members of 'struct wctdm'.
The location where some of the other members of 'struct wctdm' are initialized
were moved so that wctdm_back_out_gracefully always has a fully formed
structure to work on.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9955 a0bf4364-ded3-4de4-8d8a-66a801d63aff
We can already use the module type to determine presence of a module to
check. This also moves the background polling of the modules until after
the board is completely initialized because the module type may change
while the different types are being probed. This also means that we need
to preset the shadow registers for the FXS because otherwise the shadow
register will not have been read before the first time it's checked for
a power alarm.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9954 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Both limit the amount of junk in the kernel log and also prevent dahdi_cfg
from running indefinitely if there is a module with a hardware problem which
prevents it from completing the startup sequence.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9953 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Part of increasing system startup speed.
Splitting these two operations facilitate checking if there is a module
present synchronously on driver load from the actual load of the firmware and
configuration of the channels.
This will allow the presence of the VPM module to be flagged on the span
before registration, but load and configuration can happen in the background.
When the modules are eventually loaded via udev, there will be enough time
from the time the drivers are loaded to when dahdi_cfg will run to complete
the firmware load, eliminating the need to block the driver here.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9951 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In my opinion naming the VPM workqueues for each board is not worth the
extra complexity.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9950 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Ensures that a single run of the interrupt service routine is consistent
about whether there are VPMADT032 commands to process or not.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9949 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This message also duplicates what is in the /etc/dahdi/system.conf file
and should only be necessary when troubleshooting problems.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9948 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is trivial cleanup. Fixing up a couple of places that followed a
kmalloc with a memset to 0 and also sneaked in one ARRAY_SIZE usage
change.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9947 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The firmware load of the VPMADT032 was moved to startspan because a
quad-span card in the same system would would lock interrupts for
several seconds to load VPMOCT064/128 firmware. Now that the wct4xxp
driver no longer locks interrupts while loading its VPM module this
driver can move the VPMADT032 check/load back to module load time.
This is also required so that the presence of a hardware echo canceler
is marked on the span before it is registered with dahdi-base.c.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9946 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is always true currently but will not necessarily be in the future.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9945 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Currently the board will always be ready if the module initialization
function is complete but this change will facilitate allowing some of
the more time consuming configuration steps to happen in parallel on
system start.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9944 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This defines a NULL value for the name of an echocan as invalid. This
will allow dahdi_genconf to probe for the presence of a hardware echocan
on a channel by trying to attach one. If there is not a hardware echocan
available DAHDI_ATTACH_ECHOCAN ioctl will return -EINVAL if 'hwec' was
specified as the name of the echo canceler now.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9943 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Not quite ideal, but this seems to be the most straightforward way to
know when someone is trying to monitor the preec stream on a channel.
This callback allows the board driver providing the span an opportunity
to setup the hardware preecho monitoring as needed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9942 a0bf4364-ded3-4de4-8d8a-66a801d63aff
dahdi_ec_chunk is the function that saves the received audio and places
a signed linear copy of it in the pre echocanceled buffer on the
channel. By splitting the input and output of this function into two
parameters, a driver that can provide separate pre and post ec streams
can pass them independently to DAHDI, without worrying about DAHDI
overwriting a stream that may have already been echocanceled by the
hardware.
Previously, the dahdi_ec_chunk interface took a received audio buffer
and overwrote it after canceling the echo. Now the input and output
from the function are broken up in order to support hardware echocans
that have a different preechocan stream.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9941 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change ensures that the dahdi_span_ops callbacks are not called
with any spinlocks held, and that the module is pinned in memory, and
also passes the struct file * pointer to the callbacks.
Passing the file pointer to the callbacks allows the board drivers to
check any flags on the file descriptor used to configure the
span/channel. The intent here is to allow dahdi_config to open the
/dev/dahdi/ctl file in a non-blocking mode in case there is a lengthy
processes that needs to happen as part of configuration.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9940 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This allows any echocan cleanup to block if necessary. Especially useful
for hardware echocans that may need to wait for hardware to complete the
cleanup process.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9939 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Some older Asterisk versions do not handle well the error message when poll is
called on an unconfigured channel. The result would be constant
__ast_read: No/unknown event '0' on timer for 'DAHDI/1-1'?
messages from Asterisk.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9937 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This duplicates information that is already in the
/etc/dahdi/system.conf file and should normally only be necessary for
the user when debugging problems.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9936 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change fixes a condition where 'dahdi_cfg -s' would always return
success regardless of whether a board driver was able to complete the
shutdown. Only impacts board drivers that implemented the shutdown span
callback.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9935 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This allows dahdi-base to know whether or not there is a VPM attached to
the module as soon as it's registered as opposed to waiting for start
span. This will simplify dahdi_genconf's task of creating a valid
configuration file.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9933 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If we always set maintstat to DAHDI_MAINT_NONE, dahdi_base will lose
track of what it thinks the current state of the span is.
For example, if you run
$ dahdi_maint -s 1 --loopback localhost
When t4_clear_maint is called, the current maintenance mode state,
'maintstat', is set to DAHDI_MAINT_NONE. So the next time you call:
$ dahdi_maint -s 1 --loopback off
dahdi-base.c will believe that the user is trying to set the maintenance
state from DAHDI_MAINT_NONE to DAHDI_MAINT_NONE and will not actually do
anything.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9932 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Do not allow the interrupt handler or another CPU to change the value
between when we get the initial value and when we write the modified
value.
Also includes a minor formatting fix where braces were not aligned, and
remove 'inline' from t4_framer_in and t4_framer_out definitions.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9931 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Turn this option on for the entire wct4xxp driver in order to quiet the
warnings in the oct612x source files. These files are from a vendor drop and
the goal is to limit the deviations from the vendor if possible.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9930 a0bf4364-ded3-4de4-8d8a-66a801d63aff
gcc-4.6 now warns about variables that are set but never used. Clean up
unused variables everywhere except the oct612x subdirectory.
The oct612x should go in a separate patch in case that needs to be
pulled out into a separate project again.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9929 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Some older Asttribanks had an empty label string. They should be ignored
when testing for a duplicate label at device probe time.
While we're at it, reduce panic level in the notice.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9925 a0bf4364-ded3-4de4-8d8a-66a801d63aff
XPP_DEBUGFS code was some code used to send BRI D-Channel data
through debugfs for, well, debugging. Unused in recent years.
Time to remove.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9917 a0bf4364-ded3-4de4-8d8a-66a801d63aff
OLD_PROC marked old and unused code that was used for writing to procfs.
It has long ago been replaced with different sysfs interfaces. Time
to remove it.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9916 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Commit r9781, "wcte12xp, wctdm24xxp: Remove unused support for booting
VPMADT032 from SPI", introduced a bug that would prevent the VPMADT032
from ever being able to complete its startup. This regression did not
make it to any releases.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9914 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Introduced in rev 9905, this bug could cause buffer events to become
disabled if the kernel was unable to access userland data.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9907 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Add BUFFEVENTS and individual buffer event channel flags so that DAHDI can
notify userspace processes when it is dropping data. This can be useful when
trouble shooting fax problems since DAHDI currently silently discards data
becasuse of scheduling latency. With this change, Asterisk could log an event
as opposed to just leaving it up to the tone detectors to figure out there was
some unexpected phase shift.
Acked-by: Shaun Ruffell <sruffell@digium.com>
(original patch by Matt Fredrickson)
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9905 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Alexandre reported that on a particular server he would get a server
crash when loading the wcte12xp driver after receiving a line about a
timeout when trying to read the mode selection jumpers.
If the driver times out when trying to read the mode selection bits
there is a serious problem and it should not try to continue on with
configuration / registration.
Reported-and-Tested-by: Alexandre Abreu <alexandre.abreu@redt.com.br>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9902 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Most of the timers added to the kernel will be configured to fire at the
same rate. This allows one "wake_up" from interrupt context to wake up
all the waiters. On one test system, I saw about a ~10% improvement in
CPU utilization when 10,000 timers were opened.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9891 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Saves ~2K bytes from the size of wctdm24xxp.ko module, which saves system
memory when the driver is loaded.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9890 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change saves around 2.5 us from the interrupt handler.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9889 a0bf4364-ded3-4de4-8d8a-66a801d63aff
It is only ever accessed in interrupt context anyway. Saves several
hundred nanoseconds from hard interrupt context.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9888 a0bf4364-ded3-4de4-8d8a-66a801d63aff
No need for the CPU to wait there for that write to flush when all the
writes will be flushed when the interrupt is acknoledged later. Saves
nearly a 1 us from the interrupt handler on a 3Ghz Xeon test system.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9887 a0bf4364-ded3-4de4-8d8a-66a801d63aff
We are in hard-irq context already, so we do not need to disable all
local interrupts. On one 3.06GHz Xeon test machine, drops the average
time in the interrupt handler from 23.10 us to 21.87 us.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9886 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Allows the board drivers to use the regular locks instead of the
irqsave/irqrestore variants.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9885 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since cli/sti are expensive instructions, if the board drivers are
calling receive/transmit/ec_span from interrupt context all local
interrupts do not need to be disabled. The board drivers all still use
the normal dahdi_receive and dahdi_transmit. _dahdi_receive and
_dahdi_transmit are the "in-hardirq" versions of those functions.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9884 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Reduces the number of locks that must be grabbed and released in interrupt
context. On one 3.06Ghz Intel Xeon test machine, drops the average time in
the interrupt handler from 29.83 us to 23.10 us.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9883 a0bf4364-ded3-4de4-8d8a-66a801d63aff
These drivers (all DAHDI drivers) should explicitly block suspend if they are
loaded.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9882 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Makes the driver a little more kexec friendly when sharing an interrupt
line with another device.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9881 a0bf4364-ded3-4de4-8d8a-66a801d63aff
voicebus_quiesce is like voicebus_stop, except that it doesn't wait for any
information to come back from the card. This prevents kexec from blocking
waiting for information from a potentially dead card.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9880 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes regression introduced in r9603 where if a channel was "dacs" with
another interrupts would be reenabled prematurely.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9878 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r9402 switched to dma_pool for the SFRAMES. This updates the network
debug device to use the dma_pools for SFRAME allocation.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9877 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If the clock shifts back, don't hang in a loop of running
process_masterspan from the timer interrupt forever.
Fixes a regression of r9407.
(closes issue #19035)
Reported by: tzafrir
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
After talking with Tzafrir on IRC, I combined the check if your far ahead
with the check if you're behind and added a '\n' at the end of the
existing "detected time shift" message. That is why this patch is
different than what is posted on issue #19035.
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9876 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r9720 disabled the LEDs on the front panel of the TDM410. This commit
restores the behavior and clarify which part of the TDM410 eframes
control the LED operation.
(closes issue #18939)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9827 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since there never was a VPMADT032 module shipped with non-volatile
memory no need to check that bit contantly in interrupt context. Also
remove the unused VPM150M_DTMFDETECT bit.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9781 a0bf4364-ded3-4de4-8d8a-66a801d63aff
These functions were accidentally left in. They should have been remove in
"wctdm24xxp: Remove code for unsupported modules." r9720
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9780 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This moves the version string into dahdi-version.c that is then linked into
dahdi-base.c and dahdi-sysfs.c. This speeds builds on slow computers since
dahdi-base.c and dahdi-sysfs.c does not need to be rebuilt if only the version
string is changing.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9777 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Switch to using the newer seq_file interface for procfs. Fixes a
race when you read the "file" while its size increases (e.g. the span
enters an alarm state).
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
(closes issue #18760)
Patches:
0001-DAHDI-linux-trunk-replace-old-proc-interface-by-mode.patch uploaded by tzafrir (license 46)
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9770 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Trival name change to increase readability in the transmitprep and
recieveprep functions. Now we clearly define if we are working with an
sframe or an eframe.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-By: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9768 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since the oct6100 API consumes less stack there is no longer a danger of
overflowing our stack during load.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9752 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This saves ~300K of kernel memory for each quad or dual span VPM. Due
to the fact that this change disables caching of the NLP words (among
other things), the time to disable the echocans appears to have
increased by ~1ms.
Before this change:
=======================================================================
0) ! 356.498 us | vpm450m_setecmode(); <--- disable
0) ! 387.762 us | vpm450m_setecmode(); <--- enable
0) ! 429.839 us | vpm450m_setecmode(); <--- disable
]# echo 1 > /proc/sys/vm/drop_caches && free -k
total used free shared buffers cached
Mem: 2005352 228368 1776984 0 132
5540
-/+ buffers/cache: 222696 1782656
Swap: 983036 0 983036
After this change:
=======================================================================
0) ! 1109.515 us | vpm450m_setecmode(); <--- disable
0) ! 339.017 us | vpm450m_setecmode(); <--- enable
0) ! 1431.460 us | vpm450m_setecmode(); <--- disable
]# echo 1 > /proc/sys/vm/drop_caches && free -k
total used free shared buffers cached
Mem: 2005352 228080 1777272 0 112
5484
-/+ buffers/cache: 222484 1782868
Swap: 983036 0 983036
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9750 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Drops the size of the wctdm_ioctl stack from 524 to 204 bytes.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9748 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The code is duplicated in the config_vpmadt032 function.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9747 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes a regression introduced in r9611. Analog spans would never become
the master since the SPANSTART ioctl is not typically called on them,
and therefore they were never marked RUNNING. The result could be audio
problems.
I'm marking this as related to issue 13205 since it's generally all
related to how should the drivers select which span is the master. I
also mark as related to issue 16165 because the problems experienced are
a result of the same fundamental issue.
(issue #13205)(issue #16165)
Reported-and-Tested-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9729 a0bf4364-ded3-4de4-8d8a-66a801d63aff
With the release of Linux 2.6.37, the Big Kernel Lock is now a compile
time option. This change adds a mutex around the one place in the code
that we already knew was dependent on the lock_kernel/unlock_kernel
calls for serialization and drops the other calls to
lock_kernel/unlock_kernel if CONFIG_BKL is not defined.
This is *mostly* the dahdi-no-bkl.patch with a few minor whitespace
changes, the global_dialparmslock made static, and a warning added to
let people know they are running an experimental configuration.
(issue #18604)
Reported by: jkroon
Patches:
dahdi-no-bkl.patch uploaded by jkroon (license 714)
Signed-off-by: Jaco Kroon <jaco@uls.co.za>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9721 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The VPM100 and S100M modules are no longer supported. Analog cards supported
by the wctdm24xxp are still compatible with the S110 and VPMADT032 modules.
DAHDI-302
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9720 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Folded XPD_STATE() "protocol method" into the card_state() method.
It was only called from these (otherwise empty) methods.
Also it is not a "protocol method" for a very very very long time.
Signed-off-by: Oron Peled <oron@actcom.co.il>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9715 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Caller to CALL_XMETHOD() no longer need to explicitly pass xbus
(calculate xpd->xbus)
* Create CALL_PHONE_METHOD() similar to CALL_XMETHOD() -- inlining
the extra parameters (more readable)
* Reverse parameter order in PHONE_METHOD() and CALL_PHONE_METHOD()
to be consistent with XMETHOD() and CALL_XMETHOD()
* Rename XPD_STATE phonedev method to card_state:
- Consistency with other phonedev methods.
- These calls now Wrap internal calls to XPD_STATE protocol HOSTCMD
in PRI, BRI, FXS, FXO
Signed-off-by: Oron Peled <oron@actcom.co.il>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9706 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Add IS_PHONEDEV(xpd) macro
* Reject dahdi_register_xpd()/dahdi_unregister_xpd() for non-PHONEDEV
* Make sysfs 'offhook' attribute contain '\n' if empty (no channels)
* Skip PHONEDEV related xbus_tick() parts -- we still want to process
the end of it for the card_tick() calls.
* Remove BUG_ON() for missing phoneops
(also remove old duplicate test for XBUS_IS...)
* Call XPD_STATE method only for PHONEDEV XPD's
Signed-off-by: Oron Peled <oron@actcom.co.il>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9705 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Allow having XPDs that represent a device that is not a span.
* Refactor all span related data from 'struct xpd' to 'struct phonedev'
* Refactor span related methods into 'phonedev->phoneops'
* Refactor phone related initialization into phonedev_init()/phonedev_cleanup()
Signed-off-by: Oron Peled <oron@actcom.co.il>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9704 a0bf4364-ded3-4de4-8d8a-66a801d63aff
_t4_remove_one is now used during module initialization so it should not
be placed in the exit section of the module.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9650 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Eliminates the interruptible_sleep_on deprecated and prevents the driver from
triggering the SLEEP_ON_BKLCHECK warning.
It is still desirable to convert the cmdq to something more like what is in
the single span to eliminate the need to schedule the sleeping process every
millisecond while we're waiting for the command to complete.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9646 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Just clarifying a parameter that is never updated.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9644 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Move the description of the master span processing to above the
process_masterspan function.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9643 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This fixes a regression introduced in r9603. That commit removed
DAHDI_CONF_DIGITALMON handling (which is used to natively bridge two
channels that cannot be crossed in the board driver / hardware) since I
mistakenly thought that it was only part of the DACS handling. The
symptom of the regression is muted audio when Asterisk tries to natively
bridge two channels.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9642 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Move pseudo channel numbers up into a high range so that their presence
does not interfere with assigning channel numbers for the channels
implemented on spans. Otherwise, if a pseudo channel was opened up
before an expected span was registered, all the channel numbers in the
newly registered span would be bumped up one. This does limit the number
of real channels that a single system may have registered to 32K (but in
dahdi-linux 2.4.0 and below you were limited to 1024 channels anyway,
both real and pseudo).
Also, the string name of the Pseudo channel is now based off the
number of Pseudo channels and not the total number of channels.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9637 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If dahdi_register fails, we would like the error to propagate to the
user who ran modprobe.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9636 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Extended reset is needed primarily with the PCI express version of the
dual and quad-span cards. Enable it by default for those cards and
allow it to be forced on or off globally for the driver as a compile
time option.
The options to force it should be able to come out if there aren't any
further reports that the compile time option needs to be set.
DAHDI-773
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9635 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Now that makefw has the proper name, the rule to create it is
automatically generated by Kbuild. Removed.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9632 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If we tell Kbuild (at least of some versions) that the host program is
$obj/makefw , it will attempt to create the full path of $(obj) for it
under the current $(obj).
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9630 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Refactor SysFS and device-related code to drivers/dahdi/dahdi-sysfs.c .
* Move common headers to drivers/dahdi/dahdi.h .
This commit merely moves existing code and should have no functional
change.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9628 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Separate out device generation in dahdi_[un]register to separate
functions.
* As we don't keep anywhere the information of whether or not
* there's
an existing device node for a channel, I abuse an unused flag:
DAHDI_FLAGBIT_DEVFILE (25), to mark if the channel has a sysfs node.
DAHDI_FLAGBIT_DEVFILE is expected to be replaced later on with a proper
pointer to the device (or embedding of the device). I prefer a simple
flag for now as it does not break ABI.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9625 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Separate out device initialization and removal functions:
dahdi_sysfs_init() and dahdi_sysfs_exit(). A safer way of
generating the main device files.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9623 a0bf4364-ded3-4de4-8d8a-66a801d63aff
dahdi_check_conf() acqurires the locks as needed when scanning the
channels and should not be called under any spinlocks.
Fixes a regression that Tzafrir reported in #asterisk-dev that he could
trigger via "asterisk -rx 'channel originate Local/600@demo
Application Meetme 3000,d'"
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9621 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This fixes a regression from r9609 that Tzafrir reported. If you
register multiple spans, then remove the first span and try to register
a new span with more channels then the old span, you could end up with
multiple channels with the same number.
This change ensures that spans are ordered and that channels on a span
are always contiguous and ordered in relation to the spans.
In previous released versions of DAHDI (2.4.0 and below) this condition
would result in spans that may not have contiguous blocks of channels.
So it fixes both a recent regression and improves the behavior.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9617 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The default tone lengths are compile time options and they were in
digits.h to make it easy for users to patch. Most of these settings are
potentially overridden from user space via the DAHDI_SET_DIALPARAMS
ioctl currently regardless of these settings.
In r9597 I moved digits.h directly into dahdi-base.c since I thought it
was broken out for sharing between compilation units as opposed to
ease patching.
I also changed the units of the default options to ms instead of in
samples. This way if the sampling frequency changes the user will not
need to update the defaults.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
asterisk-dev-reference: 4D236FD7.30707@digium.com
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9616 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is a cleanup as part of simplifying reference counting for the
spans.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9612 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When a span goes into alarm it will look for a potential new master
span. For dynamic spans that are running their processing in the
sync_tick callback, the chan_lock will already be held. Therefore,
push the locating of a new master out to the global workqueue.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9611 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since there isn't a fixed array to hold all the channels, and also limit
the total number of channels that can be created, we'll add a module
parameter to allow the system administrator to specify the maximum
number of pseudo channels. This is to prevent a potentially
non-privledged process from consuming too much CPU (since all pseudos
are checked each "tick" for conferencing) and kernel memory.
By default the number of pseudo channels is limited to 512. Change the
default limit with:
]# modprobe dahdi max_pseudo_channels=<new limit>
or at runtime with:
]# echo <new limit> > /sys/module/dahdi/parameters/max_psuedo_channels
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9610 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Remove the remaining locations the 'chans' array was referenced but keep
the observable behavior the same. Namely, channels are numbered in
registration order. Only now it's possible to renumber channels easily
since their number is not also their implied location in the 'chans'
array.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9609 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In dahdi_chec_conf, dahdi_chan_unreg, and dahdi_ioctl_confdiag maxchans
and DAHDI_MAX_CHANNELS was used to scan through all the channels. Since
the channels are stored on the list of spans and list of pseudo
channels, we can directly iterate through those lists. This also paves
the way for removing the arbitrary limit on the number of channels in
the driver.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9608 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Part of getting rid of global chans array. We need to search the list
of spans and the list of pseudo channels. While this is slower than a
direct index into a 'chans' array, the places where this function is
called are not in the 'hot' path but instead part of channel
configuration and conferencing setup.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9607 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Streamlines the function a bit by grouping the three conditions that
would cause the channel receive to be completely skipped.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9606 a0bf4364-ded3-4de4-8d8a-66a801d63aff
IMO this improves readability of dahdi_receive and dahdi_transmit, and
the compiler can decide if it is better to inline this in with the
caller or break it out into a separate function.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9605 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When we're in monitor mode, we can save a pointer to the channel we are
monitoring directly instead of dereferencing the 'chans' array each
time.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9604 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This both removes the need to reference the 'chans'
__dahdi_process_putaudio_chunk and __dahdi_process_getaudio_chunk, and
allows the dahdi_receive / dahdi_transmit logic to be streamlined. DACS
channels can no longer be echocanceled if crossed. However, if a
channel was DACSed with dahi_cfg it couldn't have been echocanceled
anyway since the echo cancelers are disabled on the channel by default.
This change was originally contained in a patch kpfleming had floating
around. I split it up and merged it.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Kevin P. Fleming <kpfleming@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9603 a0bf4364-ded3-4de4-8d8a-66a801d63aff
There is no need to check the flag on the master channel when processing all
the slave channels. Originally part of a patch kpfleming had floating around.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Kevin P. Fleming <kpfleming@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9602 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Eliminates the need to look for the channel number twice.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9599 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Spans are no longer added to a static array, but they are chained
together in a list. DAHDI_MAX_SPANS, while no longer used in the
kernel, is still in include/dahdi/user.h since dahdi tools is currently
using it.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9598 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Clarify that these definitions are not / no longer used outside
dahdi-base.c.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9597 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Mainly I wanted to document that the global_dialparams is protected by
the BKL so that it can be closely checked when lock_kernel is removed
from DAHDI.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9596 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change primarily is a memory reduction. Most users only ever have
a single tone zone loaded so we can save some mostly unused pointers by
using a list instead of an array. Since we also have a pointer to the
dahdi_zone in struct dahdi_chan, we also don't need to store the integer
that is an index into that array. This saves 4 bytes for every channel
allocated in the system. Finally, we don't need a separate default_zone
member since we're on a list, we can define the first element on
the list to always be the default zone.
Additionally, all reference counted structures in the drivers should
standardize on kref as much as possible for simplicity.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9594 a0bf4364-ded3-4de4-8d8a-66a801d63aff
kasprintf will be used in upcoming changes and it's not supported on
RHEL4 kernels. This change essentially backports it.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9593 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Might help when someone wonders why they are now getting errors about
"lock_kernel" being undefined.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9592 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Not only should you not reach that line, it's impossible for you to
reach that line.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9591 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Do not allocate the structure with GFP_KERNEL under the lock in
dahdi_echocan_factory_register and closes a leak in
dahdi_echocan_factory_unregister.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9590 a0bf4364-ded3-4de4-8d8a-66a801d63aff
rwlocks are slowly being deprecated because they typically do not
provide the performance increase expected. Most of the
ecfactory_list_lock acquiring is during setup and not in the hot path
anyway, so we can just use the simpler spinlock semantics without the
overhead of a semaphore or mutex.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9589 a0bf4364-ded3-4de4-8d8a-66a801d63aff
rwlocks are deprecated and there aren't that many places where read_lock
was called on the lock anyway.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9588 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since the return value is not defined/used just return void.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9587 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is a trivial cleanup to primarily to remove the #ifdef test out of
process_masterspan.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9586 a0bf4364-ded3-4de4-8d8a-66a801d63aff
There is already a safe string copying function in all the kernels DAHDI
currently supports.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9585 a0bf4364-ded3-4de4-8d8a-66a801d63aff
2.6.25 added the DEFINE_PCI_DEVICE_TABLE macro to make sure that the
pci_device_id tables are put into the correct section in the binary.
Convert all the places where the tables were defined to use them.
This is linux-2.6 commit where the change went in along with the
rationale: 90a1ba0c5e39eeea278f263c28ae02166c5911c8
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9584 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Normally, spans are accessed via channels, which increment the reference
count on the supporting module as part of the open call. When operating
on spans by number we are susceptible to a module_unload while we are
accessing the span.
Renames find_span to span_find_and_get to indicate that we're both
finding the span by number and increasing the reference count on the
span. Spans themselves don't currently have reference counts, but we
can increment the reference count on the module that owns the spans.
This will prevent the module that has the span from unloading in the
middle of a span_config call, which in the case of the wcte12xp can take
awhile since the VPM firmware is loading.
Hopefully in the near future the spans themselves will be reference
counted directly.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9583 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Some spans, specifically dynamic local spans, should never be the timing
master since they are dependent on some other timing source driving
them.
The bit in 'struct dahdi_span' is named cannot provide timing so that by
default the other drivers will set it to 0.
This is loosely related to issue #13205 but doesn't address any of the
other elements of that issue about how to allow the user to configure
what the master span order of succession is.
(issue #13205)
Reported by: biohumanoid
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9581 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Also makes it safe to unregister a dynamic driver when there aren't any
open channels on the dynamic spans.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9580 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This allows the pvt member to be set under lock without holding the lock
through the call to create destroy.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9578 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Running in tasklets does not work well when dahdi doesn't have a span that is
acting as the master. In this case, process_masterspan is being called in
system timer that may not be running at 1ms intervals. The end result is that
the dynamic_run function isn't called for every chunk processed, and there is
data loss.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9577 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Dynamic spans that are unable to provide their own timing, like dahdi
local spans, typically derived their timing source from
dahdi_dynamic_ioctl(0,0) call in process_masterspan.
This change uses the sync_tick member of dahdi_span_ops instead so that
dynamic operations do not happen on a span until it is fully registered.
Also removes the check for dahdi_dynamic_ioctl in process masterspan for
those users that never load a dynamic span.
This was originally suggested in a comment on:
(issue #13205)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9576 a0bf4364-ded3-4de4-8d8a-66a801d63aff
2.6.9 is the earliest kernel version currently supported by DAHDI.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9575 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Move the try_module_get/module_put calls from the various dynamic
drivers into the "core" dahdi_dynamic.c file itself. This way, a
reference count can always be held while calling through the function
pointers. This is enabled by adding an .owner field to 'struct
dahdi_dynamic_driver'.
Dynamic spans are also unique in dahdi in that they require a "dahdi_cfg
-s" to stop them and release the references on the modules. This is
counterintuitive. This change makes sure they are reference counted just
like other spans and on driver unload, if there aren't any open handles
from userspace, they will take care of unwinding themselves.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9573 a0bf4364-ded3-4de4-8d8a-66a801d63aff
dahdi_dynamic can be converted to use kernel idiomatic reference
counting since DAHDI only supports 2.6.9+ kernels now.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9571 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The return value from the transmit callback function was not used
anywhere, and is now removed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9570 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Replaces all the 'z' references to 'd' as appropriate and cleans up any
formatting problems that popped up as a result. The intent here is to
reduce confusion in the future as someone may wonder what the 'Z's refer
to.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9567 a0bf4364-ded3-4de4-8d8a-66a801d63aff
It's possible for dahdi_dynamic_loc spans to be "peered" before the
dahdi_span is fully register. Do not call dahdi_dynamic_receive on any
peers before they are fully registered.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9566 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is a trivial formatting change in order to not introduce any warnings.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9565 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The memory saved by using a singly linked list does not, in my opinion,
outweigh the benefit of using the standard kernel macros.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9564 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Hopefully will eliminate any questions about what the 'z's are supposed
to represent.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9562 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This file is now in drivers/dahdi/voicebus folder. This file should
have been removed when the Gpak API was moved out of the individual
board drivers.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9559 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is a very slight performance improvement. Eliminating the need to
save the IRQ flags is probably more of a boost than grabbing and
releasing the reglock.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9558 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Mostly linux/errno.h was included more than once.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9557 a0bf4364-ded3-4de4-8d8a-66a801d63aff
dahdi/wcb4xxp driver used with Digium Wildcard B410 quad-BRI PCI card
unable to communicate with another ISDN device (ISDN phone, another port
of B410). It appears that B-channels are capable to transport data, but
D-channel is not.
Debug output added into the driver shows that packets are transmitted to
the D-channel, but no packets are received. Further investigation shows
that no interrupts received from Rx FIFO associated with D-channel,
although packets are delivered to the FIFO. I've found that problem is
in improper usage of chan->chanpos while indexing the fifo index
(bspan->fifos): chanpos starts from 1 and fifos starts from 0.
Therefore, garbage read instead of fifo number.
(closes issue #14834)
Reported by: vvv
Patches:
dahdi-linux-complete-2.2.0-rc1.patch uploaded by vvv (license 741)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9555 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Instead of using pci_set_drvdata embed the 'struct voicebus_operations'
directly in the context so we can use container_of to find the context.
This resolves a problem where the 'remove_one' callback gets an invalid
pointer to 'struct t1' if the VPMADT032 is in the middle of a reload
when the module is unloading. DAHDI-783.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9554 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is instead of initializing the waitq each time the channel is
opened or closed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerreicks <rmeyerreicks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9549 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since we've now switched to wait_event_interruptible calls, we have a
condition that we can check when we're awoken. This allows us to
combine the separate wait queues into a single queue.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerreicks <rmeyerreicks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9548 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Makes it a little more clear what it is we're really waiting for.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerreicks <rmeyerreicks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9547 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is a cleanup patch to make it a little easier to see what the bits
mean.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9543 a0bf4364-ded3-4de4-8d8a-66a801d63aff
There are some platforms where the read-line multiple transaction causes
packets to be dropped in the voicebus pipeline. The only observable
behavior is that packets just go "missing" in the pipeline. This also
only appears to affect PCI cards.
A typical 'symptom' of this problem is you may see IRQ misses increasing
without any corresponding "bumps" in latency in the kernel message log.
Normally, IRQ misses are correlated to latency bumps since that is an
indication that the host was not able to service the card interrupt in a
timely fashion. DAHDI-510 DAHDI-774
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9542 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The 'pdev' member already contained a pointer to what 'dev' was pointing
to. Also ensure most of the changed lines are under 80 characters.
There are two lines that are were too deeply nested to do anything
sensible.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9540 a0bf4364-ded3-4de4-8d8a-66a801d63aff
rwlock is slower than normal spinlocks and this lock is rarely contended
for. Also noticed that the vpmadt032_module_init function is now (was
already) redundant since all the elements initialized in it were already
initialized.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9538 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The mode module parameter is only acted on during module initialization.
We shouldn't allow anyone to change it after the driver is already
loaded.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9537 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Span registration is the last step in during initialization and it
should be the first on unregistration. I also was hit by this when
looking at adding other members to the span and made the assumption that
the span was in a consistent state during unregistration.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9536 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reduces the chance that another interrupt will interfere with the
recovery process. Otherwise it is possible that the hardware advances
past the position that we think it is currently at.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9535 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Reading 0xffffffff from the registers is a different error than just not
coming out of reset. Add a little extra debugging information.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9534 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes a regression introduced in r9510 which saves a pointer to the ops
member of a channel's span before checking if the channel is a pseudo.
Psuedo channels do not have spans.
(issue #18463)
(issue #18422)
Reported by: alecdavis
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9530 a0bf4364-ded3-4de4-8d8a-66a801d63aff
I apparently forgot all about HPEC when updating the echocans for the change
in the factory and echocan ops structures related to echocan naming. The HPEC
wrapper should now be up to date with the rest of DAHDI.
Signed-off-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9526 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Changed the echocan factory name to a function (get_name) called to get the
name. This allows a factory to return a different name when being called in
reference to a channel such as in the case of hardware echo cancellers. To
further accommodate this change for HWEC, a new echocan_name function was
added to the span ops struct and is used in hwec_factory in dahdi-base for
all cards that support hardware echo cancellation.
Signed-off-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9524 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This field was redundant and was only used in places where the factory's name could be used.
Signed-off-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9523 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Remove the code that allowed hardware echo cancellation to automatically
override software cancellation and prevented SWEC from working at all on a
card if HWEC was installed. All EC now uses the standard modular EC interface.
Additionally, the "SWEC" identifier on channel lines in /proc/dahdi has been
changed to "ECTYPE" to avoid confusion.
Signed-off-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9521 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change adds an echocan factory to dahdi-base that will allow hardware
echo cancellation to use the same interface as the current software echo
cancellers. The additions in this commit will not have any effect until the
current HWEC mechanism is removed.
Signed-off-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9520 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The loopup/loopdown T1 maintenance feature in the single through quad-span
drivers now function properly, according to AT&T TR54016, by sending a
full rate pattern down the line. T1.403 ESF/Data Link patterns are not
supported currently.
Also grouped all the maint reset register clears under a single irq lock
to crank the performance up past 11.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9516 a0bf4364-ded3-4de4-8d8a-66a801d63aff
DAHDI_MAINT_LOOPSTOP is being removed due to the redundancy with
DAHDI_MAINT_NONE. Also removing some timing logic, as amount of time a
loopup or loopdown signal is held on the line, is now defined in
userspace with dahdi_maint.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9515 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The dahdi_span->maintq wait queue was very old and not being used so it
has been removed.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom..com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9514 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The wcte12xp does all the checking for alarm in a user space workqueue.
Most of this time is spent sleeping waiting for reads from the framer to
complete. Tasks in uninterruptible sleeps are added to running tasks
for the purposes of calculating load average. This change makes the
sleeps interruptible so as to not affect the load average as much.
For example, the following command will load and configure the driver and
then print the load average every 10 seconds.
]# modprobe wcte12xp && dahdi_cfg && ((x=12)); while [[ $x -gt 0 ]]; do cat
/proc/loadavg; sleep 10; let x=$x-1; done
With this change:
0.29 0.10 0.02 1/101 29945
0.24 0.10 0.02 1/101 29967
0.20 0.09 0.02 1/101 30019
0.17 0.09 0.02 1/101 30041
0.15 0.09 0.02 1/101 30062
0.12 0.08 0.02 1/101 30085
0.10 0.08 0.02 1/101 30107
0.09 0.08 0.02 1/101 30129
0.07 0.08 0.02 1/101 30151
0.14 0.09 0.02 1/101 30173
0.12 0.09 0.02 1/101 30195
0.10 0.08 0.02 1/101 30217
(and I've seen it get down to 0.0)
Before this change:
0.57 0.22 0.07 1/101 31920
0.48 0.21 0.07 1/101 31942
0.48 0.22 0.07 1/101 31964
0.48 0.23 0.08 1/101 31986
0.41 0.22 0.07 1/101 32008
0.42 0.23 0.08 1/101 32030
0.43 0.24 0.08 1/101 32054
0.45 0.25 0.09 1/101 32076
0.45 0.25 0.09 1/101 32098
0.46 0.26 0.10 1/101 32120
0.47 0.27 0.10 1/101 32172
0.39 0.26 0.10 1/101 32194
(closes issue #18142)
Reported by: foxfire
Tested by: foxfire
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9512 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If chan->span->ops->open() fails then the reference count of the module
implementing the board driver will not be decremented. The result is a
module that would always be "in use" and unloadable.
This change makes sure to release that reference when open failed.
(closes issue #18422)
Reported by: avarvit
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Angelos Varvitsiotis <avarvit@admin.grnet.gr>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9510 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If the span reports that it supports hooksig, DAHDI may fail to use RBS.
So remove a call to that stub function.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9506 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This fixes an annoying, though harmless issue: if Asterisk decides to send
voicemail messages to a channel (CAS, configured as FXS), We can't do
anything useful with them. So ignore them to avoid scary-looking messages
(from report_bad_ioctl()).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9505 a0bf4364-ded3-4de4-8d8a-66a801d63aff
There were some routes through the failure paths in __voicebus_init() where a
registered memory region was not subsequently released. This change closes
those paths.
The result would be on subsequent loads of the driver after hitting the
failure condition you would see "IO Registers are in use by another module."
in dmesg.
request_mem_region/release_mem_region should most likely be converted to
devm_request_region and devm_release_region introduced in 2.6.20
(commit 9ac7849e35f705830f7b016ff272b0ff1f7ff759) which was introduced for
reasons just such as this.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9503 a0bf4364-ded3-4de4-8d8a-66a801d63aff
There were several cases where interruptible_sleep_on() was being used
as a ms timer, since the assumption is that the board will interrupt at
even 1ms intervals. We can replace these cases with msleep directly to
clarify that we're just waiting.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9501 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The primary change is to make clear that the wait result is not ever to
be returned by the function. There are also edits to remove some
comments that were expressed clearly in the source already and ensure
that the iomux member of 'struct dahdi_chan' is only accessed under the
chan->lock.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Sean Bright <sean.bright@gmail.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9497 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This fixes a regression introduced in revision r9466. Before this patch
one might see "I/O MUX failed: Success" messages on the Asterisk console
since the return from ioctl was > 0.
Signed-off-by: Sean Bright <sean.bright@gmail.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9496 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Reworking tsearle's patch to fit with coding guidelines and make
process_masterspan a bit easier to read.
(closes issue #16831)
Reported by: tsearle
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9494 a0bf4364-ded3-4de4-8d8a-66a801d63aff
It can now be enabled by un-commenting the CONFIG_DAHDI_MIRROR define in
include/dahdi/dahdi_config.h
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9492 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Adding the patch from the issue with various fixups to fit style and
checkpatch
(issue #16831)
Reported by: tsearle
Patches:
driver_v2.patch uploaded by tsearle (license 373)
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9491 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The first place new_master is referenced after the definition is to
assign it to the value of the current master.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9489 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Logs the RBS bits to dmesg, for troubleshooting, for all drivers that call
dahdi_rbsbits(). Added the DEBUG_RBS bit in the debug module parameter
bitfield.
(issue #18025)
Acked-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9487 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If we're waiting for tens or hundreds of milliseconds we will just go to
sleep instead of spinning.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9471 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'usecount' was removed in revision 6926 but parts were accidentally
merged back in revision 8123 as part of the Hx8 merge.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9470 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'schluffen()' essentially duplicates the functionality of the standard
Linux 'interruptible_sleep_on()' function.
There may still be some race conditions that can be closed here, but
most of the command queue processing is sloted for conversion to
something more like in the single span driver in order to reduce the
time in interrupt context spent scanning for commands to the modules.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9469 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Also moves the dahdi_txlevelnames array into the dahdi_lboname function,
which is the only place it it used.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9468 a0bf4364-ded3-4de4-8d8a-66a801d63aff
wake_up_interruptible() will change the state of waiting tasks back to
TASK_RUNNING, therefore, we want to ensure we set TASK_INTERRUPTIBLE
before checking the conditions that we're going to sleep on.
In practice, this closes a small window were the caller may be put to
sleep when the condition is true, and have to wait for another event to
come in order to wake from the sleep.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9467 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Just a cleanup patch that moves code into a standalone function. Real
change to follow.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9466 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'interruptible_sleep_on()' is the Linux equivalent of 'tsleep()'. When
we're sleeping for a condition, we can also just use
wait_event_interruptible to close a potential race where the condition
goes true between the time we checked it and when we go to sleep waiting
on the event.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9465 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Using semaphores as mutexes was removed from the kernel in 4882720b267b.
Just use straight semaphores now. 'DECLARE_MUTEX()' -> 'DEFINE_SEMAPHORE()'
and 'init_MUTEX()' -> 'sema_init()'.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
LKML-Reference: <20100907125057.562399240@linutronix.de>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9464 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Conference links do not appear to be in use anymore and they are now
removed. I could not find any references to this ioctl in the asterisk
repository, or zaptel user space tools.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9463 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Renamed the NMF workaround message to the more informational
crc4-multiframe (mis)alignment message.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9461 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When using conference mode DAHDI_CONF_DIGITALMON ensure conf_chan is
set. Otherwise we dereference a NULL 'conf_chan'.
Fixes regression introduced in revision 9381
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9457 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes a regression introduced in revision 5916 where FXS modules based
on the 3210 were not properly detected.
(closes issue #18184)
Reported by: bsexton
Patches:
dahdi-fxo-detect.diff uploaded by bsexton (license 1133)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9456 a0bf4364-ded3-4de4-8d8a-66a801d63aff
DAHDI does not support any kernels older than 2.6.9. No need
to keep the old HDLC interface support around.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9447 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'cmd_dequeue_vpmadt032' in the wctdm24xxp and wcte12xp drivers no longer
care about which frame they are on. The command will be packed into the
eframe specified by "writechunk".
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9446 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'zt' is a carry over from the Zaptel days.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9445 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Push all tests for the DAHDI_FLAGBIT_NETDEV flag behind a
'dahdi_have_netdev' function so if CONFIG_DAHDI_NET is not defined the
compiler can just remove all the flag tests. Also, makes sure that the
bit is checked / set atomically.
(closes issue #9379)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9444 a0bf4364-ded3-4de4-8d8a-66a801d63aff
It can be necessary to have low frequency filter for tx signal of DAHDI.
Otherwise, low-frequency signal from IP can reach a leased line, and
return back with nonlinear distortions. This will break an echo
canceler.
(closes issue #13562)
Reported by: biohumanoid
Patches:
dahdi_echocan_oslec.c.patch uploaded by biohumanoid (license 459)
I slightly modified the above patch in order to use echocan_process_tx
as the interface.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9443 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Add optional interface to allow software echo cans to process the
transmitted samples. Can be used for things like DC removal.
I used the following patches uploaded by biohumanoid but changed the
name of 'echocan_hpf_tx' to 'echoan_process_tx and put the changes
behind a compile time option.
(issue #13562)
Reported by: biohumanoid
Patches:
kernel.h.patch uploaded by biohumanoid (license 459)
dahdi-base.c.#2.patch uploaded by biohumanoid (license 459)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9442 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In zaptel commit 4096 [1], all the debouncing of ring signals were moved
into software as opposed to using the ring validation circuit in DAA.
That commit failed to remove the initial check and set of the ring
validation circuit.
[1] http://svn.digium.com/view/zaptel?view=revision&revision=4096
(closes issue #16894)
Reported by: rde42
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9441 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If the DSP ever finds it's way into a bad state it can be possible for a
timeslot to get 'wedged'. All attempts to create a channel in a wedged
timeslot will fail and the WARN_ON macro can quickly fill the logs.
This change adds some more debugging information (which timeslot is wedged)
along with the result code from the DSP and puts it all behind a
printk_ratelimit.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9437 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Just use the standard way to print messages associated with a particular
device. Also dropped the "Attached to device at" message since that
information is now printed on every print.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9436 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'service_dte' was only called in one place and is only two lines. I do
not think it is adding much anymore. Also, let compiler should decide if
'service_rx_ring' and 'service_tx_ring' should be inlined.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9435 a0bf4364-ded3-4de4-8d8a-66a801d63aff
It appears that in Centos 4, the version of tar doesn't like the -o
flag, but will honor the --no-same-owner flag.
(closes issue #16063)
Reported by: tzafrir
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9434 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Setting this configuration option would not have had any impact when a
hardware echo canceler was in use.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9432 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes a regression singce r8873: if pri_protocol is not explicitly set
(in /etc/dahdi/xpp.conf) and the device has (licences for) less than 4
"PRI" (E1/T1) ports, the initialization script will attempt to read from
a non-existing SysFS file, and bail out, resulting in a the device
failing to initialize.
For those non-existing ports we can just skip that part of the
initialization. So we just skip it.
Work around: explicitly set pri_protocol to E1 or T1, as needed.
Xorcom Rev: 8047. Ticket: 1334.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9430 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes a typo recently introduced that was preventing asterisk from
setting the swgains on a channel.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9423 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Make explicit what part of the union is being accessed.
(closes issue #15908)
Reported by: ys
Patches:
dahdi-dahdi_echocan_events.diff uploaded by ys (license 281)
Signed-off-by: Kinsey Moore <kmoore@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9421 a0bf4364-ded3-4de4-8d8a-66a801d63aff
