The cards affected include the TE131/3, TE235/435, A4B, and A8B.
Update all PCIe cards' firmware to increase the incoming and outgoing TDM FIFOs
to 16ms. The FIFOs will only be filled to a depth equal to the driver's latency
setting (ie. 3ms default). The total system latency is not effected. The
firmware and driver now also report the maximum DMA transaction time when in
DEBUG mode to aid in determining if the system is experiencing long PCIe
transactions (ie. TLP completion timeouts).
Decreased the maximum latency to from 20 to 12ms
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
A fresh modprobe and dahdi_cfg would cause a temporary green alarm state on the
spans for a second while the alarm debounced into RED. New logic keeps the
spans alarm state as NONE during the unconfigured state, but sets the alarm
state to RED after the framer reset in the startup logic.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Adds driver support for Digium's new te436 and te236 quad and dual span T1/E1 cards.
[removed whitespace at end of line]
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
If dahdi_span_ops.spanconfig is called multiple times in a row (like when
running dahdi_cfg; dahdi_cfg ) the tx signaling bits would go through a spurious
state that some far side devices would respond to.
Now, if the dahdi_span_ops.spanconfig callback is called, and the configuration
matches the existing configuration, we will not touch the framer.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
This is the same change for the wcte13xp driver but applied to the other
xbus-based digital card.
If dahdi_cfg set the DAHDI_CONFIG_NOTOPEN setting on the span, which it does
when the "yellow" flag is added to the span config line, then it was possible
for the span to get stuck with DAHDI_ALARM_NOTOPEN (NOP).
This is because the driver only updates the alarm state when the framer reports
that the span alarm has changed. Therefore, unless the framer goes through an
alarm transition, the fact that channels are opened was never noticed by alarm
handling routine.
Now check the alarm state directly when the first channel is opened, and the
last channel is closed.
Internal-Issue-ID: DAHDI-1103
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
This will facilitate adding another flag for open channels on a span without
needing to add a lock on the span, or taking the global lock. Currently the span
flags are protected by the global reglock. This is not longer required.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Some architectures, like arm, do not automatically pull in the definitions for
kzalloc and friends. This allows DAHDI to build on those platforms.
Originally reported to the asterisk-users mailing list here
http://lists.digium.com/pipermail/asterisk-users/2014-February/282338.html
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
This is to support users who are unable to update to the lastest CentOS 5.x.
There is no change for most users on the latest releases of their distribution.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
If the memory allocation for the new channel array fails, it would be possible
to call enable_irq() without the corresponding call to disable_irq().
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
This firmware image is able to handle system conditions that would result in
spans internmittenly going down and recovering.
Internal-Issue-ID: DAHDI-1087
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Allow certain older firmwares to delay the hard reset until a full power cycle.
This way we can "preload" newer firmware images, without requiring the user to
physically power off/on their machine.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
This makes the behavior of IRQ misses for these drivers behave the same as the
wcte12xp, wctdm24xxp, and wct4xxp drivers.
Previously irqmisses would never increase. The presence of underruns would still
show up in dmesg as latency bumps.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
These were left over from when the VPM callbacks depended on the different VPM
installed. On the wcte43x this is unnecessary.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
This was a legacy compile time option that is no longer necessary with the new
series of cards.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
It was an oversight to prevent the wcte43x and wcte13xp drivers from using
Message Signaled interrupts during the switch to the wcxb library.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
This resolves issues where, when using internal timing, the first channel of
span 3 has occassional corrupted data in transmit stream.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
If the driver is loaded with vpmsupport=0, then it was possible to create a
deadlock situation since the call into __dahdi_ec_chunk might then try to grab
the channel lock while already holding the reglock.
The purpose of grabbing reglock in the DMA routines was to protect the channel
array, which can be changed when linemode is changing. So instead, we'll
completely mask off that interrupt line from all CPUs when potentially changing
the channel array.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
From: Wendell Thompson <wthompson@digium.com>
These new cards are based on a common architecture with the TE133/TE134 as well
as the new analog cards, A4A/A4B/A8A/A8B.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
