Some architectures, like arm, do not automatically pull in the definitions for
kzalloc and friends. This allows DAHDI to build on those platforms.
Originally reported to the asterisk-users mailing list here
http://lists.digium.com/pipermail/asterisk-users/2014-February/282338.html
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
If a span was fully configured before unassigning and reassigning to a new span
type it was possible for stale values to be present in the register. When
switching from T1 to E1 via the spantype sysfs attribute this could result in a
test pattern being written.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
If a card stops generating interrupts for any reason, it can take awhile to
unload the driver while waiting for the commands to timeout. Now if there is a
problem, immediately set a bit that the card is failed so that no new commands
will be submitted.
Also, do not free and commands in submit since all commands are freed in get
results now. This prevents list/memory corruption when commands time out.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
This brings the wcte12xp driver in line with the wct4xxp driver. It also
eliminates the chance that the local side will errouneously go into loopup when
switched from E1 to T1 mode via the spantype sysfs attribute.
Internal-Issue-ID: DAHDI-1038
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
This fixes an (embarrassing) error in t1_check_sigbits in the previous commit
where I was writing pass the end of an array on the stack.
Now instead of using an array on the stack, of which all elements were not used,
the pending commands are now stored on a list. I also removed the automatic free
of commands from __t1_getresults and now the function that allocated the command
now frees them.
I believe this will be less error-prone going forward.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10700 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The frequency that the RBS registers were polled was too slow to catch the pulse
dialing digits. The result was that often times dahdi would generate WINK events
instead of PULSEDIGIT events.
This speeds up the rate at which the registers are checked from 100ms to 33ms
and also makes the process of checking the registers quicker by queing up all
the reads at once.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10699 a0bf4364-ded3-4de4-8d8a-66a801d63aff
To enable J1 mode previously one would configure the card in T1 mode and then
set the j1mode module parameter. Now "modprobe wcte12xp default_linemode=j1"
will work like the other linemodes globally for all cards manged by this driver.
J1 can also be set on a card-by-card basis in sysfs.
Also move pr_fmt to top of file so pr_xxx macros print the module name as
intended.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10696 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* This is a minimal convertion -- everything compiles and looks OK.
* We print a warning for spans registering without a spantype.
* Low-level drivers may later want (but not required)
to fold their internal representations to this canonical
representation -- it will save code and make it more readable.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10683 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Newer versions of kernel build system do not require these Makefiles and
support for kernels older than 2.6.9 are no longer supported by DAHDI.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10617 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In addition to updating the year, this also adds some boilerplate to
dahdi-sysfs.c and dahdi-sysfs-chan.c that wasn't there previously.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10560 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Certain BIOSes appear to enable ASPM even though it is not fully supported by
the platform. Also, since the PCIe links for TDM cards are always in use it
does not make sense to allow them to transition to the disabled state.
Just turn off power management on the PCIe links completely. For more
information see http://lwn.net/Articles/449448/.
Internal-Issue-ID: DAHLIN-283
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10557 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This patch removes support for kernel versions < 2.6.18, as those are
not actively supported in any major Linux distribution (except RHEL4,
which is in the "extended" support level of the product life cycle).
This removes much of the more #ifdef-rich parts of the code.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10472 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Allowing the linemode to be configured with sysfs before the spans are
assigned opens the eventualy capability for line mode to be configured
with the other physical layer settings per card. Currently linemode is
set with either physical jumpers or with a module parameter to the
wcte12xp driver that is global for all cards.
Default behavior is not changed with this commit.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10278 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'irqmisses' is more a function of the device and there are better ways
to get to IRQ for a device than storing it in any DAHDI structures.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10276 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This exposes dahdi devices in sysfs and also exposes attributes that
will allow user space to control the registration order in spans. This
facilitates loading drivers out of order yet keeping consistent
span/channel numbering, which in turn will eventually allow the
blacklist for DAHDI drivers to be removed. The default behavior,
controlled with the auto_register module parameter on dahdi is to number
the spans / channels in order like is currently done. So this change
does not introduce any new behavior by default.
* Writing (anything) to this attribute returns the span to its
unassigned state
* Fix dahdi_chan_unreg() echocan refcount
* Add safeguard against duplicate unassignment to _dahdi_unregister_span()
* Remove the span from device_node list, only in dahdi_unregister_device()
and not in dahdi_unregister_span()
* Free allocated span->span_device in span_sysfs_remove()
[is it safe?, didn't cause problem so far...]
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
dahdi: Add "hardware_id" dahdi_device attribute.
- The "hardware_id" does not change with device location (e.g: when a PCI
card is moved from one slot to another).
- Not all devices have this attribute. It is legal for it to be NULL (that
is the default for all low-level drivers that do not set it explicitly).
- When "hardware_id" is NULL, the sysfs attribute value is "\n"
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10275 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Increasingly, spans are implemented by devices that support more than a
single span. Introduce a 'struct dahdi_device' object which explicitly
contains multiple spans. This will allow a cleaner representation of
spans and devices in sysfs since order of arrival will not determine the
layout of the devices. This also gives the core of dahdi a way to know
the relationship between spans.
This generalizes similar concepts that were previously xpp specific. The
conversion of the xpp code was almost entirely done by Oron and Tzafrir.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10273 a0bf4364-ded3-4de4-8d8a-66a801d63aff
't1e1override' isn't immediately apparent what it is supposed to do by the
name. Instead 'default_linemode' module parameter can be set to "auto", "t1",
or "e1" to make it clear.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10243 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The intent here is to flag to users that the maintenance counters are
not collected for spans exported by the wcte12xp driver.
dahdi_maint before this change:
# dahdi_maint -s 1
Span 1:
>Framing Errors : 0:
>CRC Errors : 0:
>Code Violations : 0:
>E-bit Count : 0:
>General Errored Seconds : 0:
And after:
# dahdi_maint -s 1
Span 1:
>Framing Errors : -1:
>CRC Errors : -1:
>Code Violations : -1:
>E-bit Count : -1:
>General Errored Seconds : -1:
This can be combined with a change to dahdi_maint to recognize that the
errors are -1 and print an even more explicit warning.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10212 a0bf4364-ded3-4de4-8d8a-66a801d63aff
A "(VPMADT032)" string is appended to the devicetype (as shown by
dahdi_scan) for the span if one is installed. Now append '(VPMOCT032)'
if one is installed as well.
Also, for the wcte12xp driver append the VPM name to the device type after
initially probing as opposed to only after the span is configured.
(Related to issue DAHDI-890)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10203 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When the driver begins to initialize a device it conducts a read/write
test on one of the framer registers. The driver ignores the result of
that test and results in much output spammed to the kernel logs for a
failed card since the driver doesn't then try to unbind from the device.
What was getting spammed:
wcte12xp 0000:03:01.0: Timeout in t1_getreg
wcte12xp 0000:03:01.0: Wrote '0' but read 'fffffffb'
Now abort the bind if the read / write test fails.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10155 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The wcte12xp wasn't recognizing loopup/loopdown signals. The debounce was so
long that it was preventing the loopup/loopdown signals from being registered
properly. Removed the debounce entirely as it was unnecessary to the operation.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10064 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The shutdown logic requires that all CPUs see that the INITIALIZED bit
has been cleared. Otherwise it may be possible for the workqueue to run
after the hardware resources have been released.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10047 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The firmware load has been moved into a workqueue to prevent the module load
from blocking for the duration of the firmware upload. This could be up to 40
seconds. Driver prevents configuration until firmware load is finished and
is_initialized() returns true.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9998 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Support enabled for the vpmoct032 echo cancellation module for the wctdm24xxp
and wcte12xp drivers.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9997 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r9946, "wcte12xp: Move the VPMADT032 test/configuration to module load
time." introduced a race condition where it was possible for the timer
that initiates the check for the alarms to fire before the board was
marked initialized. This would result in a board that would never again
check it's alarm state since the first time the timer runs INITIALIZED
may not be set and it will not reschedule a check since it believes the
driver is unloading.
This happened because the check for the VPM was moved between when the
timer was first setup and when INITIALIZED was then set.
Now we make sure INITIALIZED is set before the timer is first setup, and
move those two operations together.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9981 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Both limit the amount of junk in the kernel log and also prevent dahdi_cfg
from running indefinitely if there is a module with a hardware problem which
prevents it from completing the startup sequence.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9953 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Part of increasing system startup speed.
Splitting these two operations facilitate checking if there is a module
present synchronously on driver load from the actual load of the firmware and
configuration of the channels.
This will allow the presence of the VPM module to be flagged on the span
before registration, but load and configuration can happen in the background.
When the modules are eventually loaded via udev, there will be enough time
from the time the drivers are loaded to when dahdi_cfg will run to complete
the firmware load, eliminating the need to block the driver here.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9951 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In my opinion naming the VPM workqueues for each board is not worth the
extra complexity.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9950 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Ensures that a single run of the interrupt service routine is consistent
about whether there are VPMADT032 commands to process or not.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9949 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This message also duplicates what is in the /etc/dahdi/system.conf file
and should only be necessary when troubleshooting problems.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9948 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is trivial cleanup. Fixing up a couple of places that followed a
kmalloc with a memset to 0 and also sneaked in one ARRAY_SIZE usage
change.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9947 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The firmware load of the VPMADT032 was moved to startspan because a
quad-span card in the same system would would lock interrupts for
several seconds to load VPMOCT064/128 firmware. Now that the wct4xxp
driver no longer locks interrupts while loading its VPM module this
driver can move the VPMADT032 check/load back to module load time.
This is also required so that the presence of a hardware echo canceler
is marked on the span before it is registered with dahdi-base.c.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9946 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is always true currently but will not necessarily be in the future.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9945 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This defines a NULL value for the name of an echocan as invalid. This
will allow dahdi_genconf to probe for the presence of a hardware echocan
on a channel by trying to attach one. If there is not a hardware echocan
available DAHDI_ATTACH_ECHOCAN ioctl will return -EINVAL if 'hwec' was
specified as the name of the echo canceler now.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9943 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change ensures that the dahdi_span_ops callbacks are not called
with any spinlocks held, and that the module is pinned in memory, and
also passes the struct file * pointer to the callbacks.
Passing the file pointer to the callbacks allows the board drivers to
check any flags on the file descriptor used to configure the
span/channel. The intent here is to allow dahdi_config to open the
/dev/dahdi/ctl file in a non-blocking mode in case there is a lengthy
processes that needs to happen as part of configuration.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9940 a0bf4364-ded3-4de4-8d8a-66a801d63aff
gcc-4.6 now warns about variables that are set but never used. Clean up
unused variables everywhere except the oct612x subdirectory.
The oct612x should go in a separate patch in case that needs to be
pulled out into a separate project again.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9929 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Commit r9781, "wcte12xp, wctdm24xxp: Remove unused support for booting
VPMADT032 from SPI", introduced a bug that would prevent the VPMADT032
from ever being able to complete its startup. This regression did not
make it to any releases.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9914 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Alexandre reported that on a particular server he would get a server
crash when loading the wcte12xp driver after receiving a line about a
timeout when trying to read the mode selection jumpers.
If the driver times out when trying to read the mode selection bits
there is a serious problem and it should not try to continue on with
configuration / registration.
Reported-and-Tested-by: Alexandre Abreu <alexandre.abreu@redt.com.br>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9902 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change saves around 2.5 us from the interrupt handler.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9889 a0bf4364-ded3-4de4-8d8a-66a801d63aff
We are in hard-irq context already, so we do not need to disable all
local interrupts. On one 3.06GHz Xeon test machine, drops the average
time in the interrupt handler from 23.10 us to 21.87 us.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9886 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Reduces the number of locks that must be grabbed and released in interrupt
context. On one 3.06Ghz Intel Xeon test machine, drops the average time in
the interrupt handler from 29.83 us to 23.10 us.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9883 a0bf4364-ded3-4de4-8d8a-66a801d63aff
These drivers (all DAHDI drivers) should explicitly block suspend if they are
loaded.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9882 a0bf4364-ded3-4de4-8d8a-66a801d63aff
voicebus_quiesce is like voicebus_stop, except that it doesn't wait for any
information to come back from the card. This prevents kexec from blocking
waiting for information from a potentially dead card.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Michael Spiceland <mspiceland@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9880 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since there never was a VPMADT032 module shipped with non-volatile
memory no need to check that bit contantly in interrupt context. Also
remove the unused VPM150M_DTMFDETECT bit.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9781 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Trival name change to increase readability in the transmitprep and
recieveprep functions. Now we clearly define if we are working with an
sframe or an eframe.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-By: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9768 a0bf4364-ded3-4de4-8d8a-66a801d63aff
2.6.25 added the DEFINE_PCI_DEVICE_TABLE macro to make sure that the
pci_device_id tables are put into the correct section in the binary.
Convert all the places where the tables were defined to use them.
This is linux-2.6 commit where the change went in along with the
rationale: 90a1ba0c5e39eeea278f263c28ae02166c5911c8
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9584 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This file is now in drivers/dahdi/voicebus folder. This file should
have been removed when the Gpak API was moved out of the individual
board drivers.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9559 a0bf4364-ded3-4de4-8d8a-66a801d63aff
