This resolves an issue with a Glenayre GL3000 Paging Terminal with v8.000
software. The Glenayre would change both A and B bits to signal on/off hook
states, but there were a couple of milliseconds between when those bits changed.
This resulted in DAHDI generating an on-hook event to Asterisk before generating
the off-hook event and therefore Asterisk terminated the call prematurely.
Looking the A and B bits before this patch:
Asterisk (AB) Glenayre (AB)
00 00 Both sides on-hook
11 00 Asterisk goes off hook to sieze line.
11 01 Glenayre starts going-offhook. On-hook event
sent to Asterisk from drivers since bits
changed but ABIT was still 0.
11 11 Glenayre finishes going off-hook. Off-hook
event sent to Asterisk since ABIT changed
from 0 to 1.
00 11 Asterisk, processes on-hook event and goes
on-hook itself to release line.
00 00 Glenayre releases line. Call fails.
After this patch:
Asterisk (AB) Glenayre (AB)
00 00 Both sides on-hook
11 00 Asterisk initiates call
11 01 Glenayre starts handling call. No event is
sent to Asterisk since only ABIT is checked.
11 11 Glanayre finishes going off-hook. Call
proceeds normally.
Internal-Issue-ID: DAHDI-1009
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Since r5021 [1], first released in DAHDI-Linux 2.2.0, it's been impossible for
user space to change the rxbufpolicy. This hasn't caused any problems and it's
safe to remove a few more of the vestiges of the rxbufpolicy from the driver.
This streamlines the code path in a few places and saves 8 bytes from the size
of struct dahdi_chan.
The user visible parts are maintained and will indicate
DAHDI_POLICY_IMMEDIATE, like it has since 2.2.0.
[1] http://svnview.digium.com/svn/dahdi?view=revision&revision=5021
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10730 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Internally in DAHDI there is always a hardware echocan factory registered and
available. Having this factory always registered allows for DAHDI to work in a
backward compatible fashion. Namely, by default DAHDI will always use a hardware
echocan if one is available unless 'hwec_overrides_swec' dahdi module parameter
is set to 0 on load. However, if there were no real hardware echocans available
in the system dahdi would still report "Echo Canceller(s): HWEC" in the
dahdi_cfg -v output since the hwec factory is always there.
After this change dahdi_cfg will no longer report HWEC as one of the available
echocans if there isn't a physical span present that actually has a hardware
echocan.
Internal-Issue-ID: DAHLIN-300
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10727 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The previous maint state was saved regardless if the base driver returned an
error or not. This caused strange behavior in dahdi tools. Moved the maint
state save to after the switch case to reflect this.
https://issues.asterisk.org/jira/browse/DAHDI-984
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10718 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* This is a minimal convertion -- everything compiles and looks OK.
* We print a warning for spans registering without a spantype.
* Low-level drivers may later want (but not required)
to fold their internal representations to this canonical
representation -- it will save code and make it more readable.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10683 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'irq' field was removed from dahdi_span in r10276 "dahdi: Remove
dahdi_span.irq and move dahdi_span.irqmisses into dahdi_device." [1]
which was first released in dahdi-linux 2.6.0.
[1] http://svnview.digium.com/svn/dahdi?view=revision&revision=10276
Reported-by: Pavel Selivanov
Internal-Issue-ID: DAHLIN-278
Patches: hdlc.patch by Pavel Selivanov (license #5420)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10634 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Instead of registering a function pointer, register a dahdi_dynamic_ops
structure that contains the owner as well as the ioctl callback. This way
dahdi.ko can bump up the reference count on dahdi_dynamic.ko before calling
the ioctl callback.
Also, use the registration mutex to guard against the module being unloaded
between the time the structure pointer was checked, and the module reference
is taken.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10623 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In addition to updating the year, this also adds some boilerplate to
dahdi-sysfs.c and dahdi-sysfs-chan.c that wasn't there previously.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10560 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Will allow the ASPM (Active State Power Management) state to be disabled on
PCIe devices before kernel version 2.6.25.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10556 a0bf4364-ded3-4de4-8d8a-66a801d63aff
DAHDI internal timing currently uses the "wall clock" to determine how much
time is passing for mixing and timers. When the wall time changes, like when
the system time is set via ntp or date, DAHDI currently will display a
"Detected time shift" message since it believes there is too much audio to
mix. There may also be audio problems if the wall time is shifting
occasionally due to slewing of the clock.
Now use a monotonic clock to determine how much real-time has passed for
timing purposes. This makes DAHDI insensitive to any changes in the wall time
on the system.
This only applies when using DAHDI's internal timer like when there are not
any telphony cards installed. There are still potential audio problems if the
platform is unable to accurately determine the passage of time.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10482 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This patch removes support for kernel versions < 2.6.18, as those are
not actively supported in any major Linux distribution (except RHEL4,
which is in the "extended" support level of the product life cycle).
This removes much of the more #ifdef-rich parts of the code.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10472 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Shortcut CLASS_DEV_CREATE/CLASS_DEV_DESTROY. No need to pass repetitive
data (and NULL) on every call.
* Create/remove fixed device files (ctl, timer, channel, pseudo) via
generic code (fixed_devfiles_create()/fixed_devfiles_remove()) instead
of repetitive code and flags.
* Try to make all removal/cleanup functions idempotent, so we can
safely call them on any failure without the need for multiple goto
destinations.
* Rename 'device_state_flags' to 'should_cleanup' and its member
flags to a better/consistent naming.
* Rename dahdi_sysfs_exit() to dahdi_sysfs_cleanup() and call it from
a new proper dahdi_sysfs_exit()
* In dahdi_sysfs_init(), handle dahdi_sysfs_chan_init() failures
* Add dahdi_dbg() message before creating/removing all DEVICES
objects.
* Also move two KERN_INFO messages to a more correct locations:
- The version reporting should be first (in dahdi-base.c)
- The "Telephony... on major" reporting should be at the end
of dahdi_sysfs_init()
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10464 a0bf4364-ded3-4de4-8d8a-66a801d63aff
show Master change to/from core timer if DEBUG_MAIN (GENERAL) flag is on.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10451 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* A parent-less device should not crash dahdi:
- Access span->parent->dev instead of span->parent-dev.parent
in soem cases.
- Access span->parent->dev via new inline span_device()
- Use span_device() in all dahdi_dev_{dbg,info}()
* Allow low-level drivers to set their device name.
- Drivers that don't use this feature get the default name
based on the parent device name
- Parent-less devices which don't set their name, fails
to register with -EINVAL
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10449 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Allows dahdi_cfg to return an error code if a board driver fails it's startup
call for any reason.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10379 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Otherwise, if the _dahdi_assign_span call fails, the dahdi_device will never
be removed from the dahdi_devices virtual bus and the board drivers will not
be reloadable.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10331 a0bf4364-ded3-4de4-8d8a-66a801d63aff
I misssed a small typo in r10328 "Extra debugging aids and messages" that
would force any span that supports a hardware preechocan to always fail
assignment with -EFAULT.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10330 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Added dahdi_dev_dbg() macro to print when we don't (yet)
have a span number.
* Added a new debug category: DAHDI_DBG_ASSIGN
* Made sure error return code paths prints helpfull messages
* Promote error messages from INFO to NOTICE
* Change some errno values from EINVAL to EFAULT (internal
errors not caused by user input)
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10328 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The test in _check_spanno_and_basechan() was off by one
(used '<' instead of '<=')
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10327 a0bf4364-ded3-4de4-8d8a-66a801d63aff
r10205 "dahdi: Check for master in DAHDI_STARTUP / resolves MeetMe
regression." did not handle the case for the wcb4xxp driver since it
would set DAHDI_FLAG_RUNNING as part of the probe. Therefore, the
DAHDI_STARTUP ioctl was never processed for it, creating a situation
where audio is missing on channels that are conferenced with channels on
the BRI spans.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10304 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* We try very hard to help asterisk understand that we unassign spans.
* Implement disable_span():
- Set span + channels to DAHDI_ALARM_NOTOPEN
- qevent DAHDI_EVENT_REMOVED
* Use disable_span():
- in dahdi_unassign_span() and dahdi_unregister_device()
- with long msleep() so asterisk has a chance to get the message
- Out of the registration_mutex so we actually context switch.
* Also return more POLLERR variants (POLLRDHUP is not portable,
should be tested).
* Also improve printk(), fix rate_limit increment (was missing)
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10285 a0bf4364-ded3-4de4-8d8a-66a801d63aff
'irqmisses' is more a function of the device and there are better ways
to get to IRQ for a device than storing it in any DAHDI structures.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10276 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This exposes dahdi devices in sysfs and also exposes attributes that
will allow user space to control the registration order in spans. This
facilitates loading drivers out of order yet keeping consistent
span/channel numbering, which in turn will eventually allow the
blacklist for DAHDI drivers to be removed. The default behavior,
controlled with the auto_register module parameter on dahdi is to number
the spans / channels in order like is currently done. So this change
does not introduce any new behavior by default.
* Writing (anything) to this attribute returns the span to its
unassigned state
* Fix dahdi_chan_unreg() echocan refcount
* Add safeguard against duplicate unassignment to _dahdi_unregister_span()
* Remove the span from device_node list, only in dahdi_unregister_device()
and not in dahdi_unregister_span()
* Free allocated span->span_device in span_sysfs_remove()
[is it safe?, didn't cause problem so far...]
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
dahdi: Add "hardware_id" dahdi_device attribute.
- The "hardware_id" does not change with device location (e.g: when a PCI
card is moved from one slot to another).
- Not all devices have this attribute. It is legal for it to be NULL (that
is the default for all low-level drivers that do not set it explicitly).
- When "hardware_id" is NULL, the sysfs attribute value is "\n"
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10275 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change will facilitate creating rules that will allow spans and channels
to be accessed by named device files instead of by numbers.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10274 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Increasingly, spans are implemented by devices that support more than a
single span. Introduce a 'struct dahdi_device' object which explicitly
contains multiple spans. This will allow a cleaner representation of
spans and devices in sysfs since order of arrival will not determine the
layout of the devices. This also gives the core of dahdi a way to know
the relationship between spans.
This generalizes similar concepts that were previously xpp specific. The
conversion of the xpp code was almost entirely done by Oron and Tzafrir.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10273 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This patch contains interim results while trying to make
device removal work correctly:
* XPP has protections to prevent dahdi unregistration while
channels are open -- they are now removed, so we can
unregister immediately.
* Handle processes in poll_wait():
- Wake them during dahdi_chan_unreg() after the channel
is gone (chan->channo = -1 or chan->file->private_data == NULL)
- Test in every wait_event_interruptible() that the channel
was not gone (chan->file->private_data)
- Return correct values (POLLERR | POLLHUP) instead of
some errno (would be important in the future if we
modify asterisk to respond correctly to this condition.
* Other issues:
- If unregistered channel is being polled, than call msleep() before
returning, to give other processes a chance (normally, asterisk
has RT priority)
- Call close_channel() from dahdi_chan_unreg() so it releases
related tonezone
* There is still a horrible race hidden by msleep(20) in
dahdi_chan_unreg()
force close channels from dahdi_chan_unreg():
* Mark them via DAHDI_FLAGBIT_OPEN
* Call low-level driver close() method if available
* What about other closing activities?
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10270 a0bf4364-ded3-4de4-8d8a-66a801d63aff
There were a couple of reports that MeetMe conferences were not
working in 2.5.0.1 and that downgrading to 2.4.1.2 resolved the
issue. This could occur if there were no analog spans in a system,
and all the digital spans were out of alarm before DAHDI_STARTUP
ioctl was called by dahdi_cfg. If the spans were *not* out of alarm,
they would be marked master when the span changes it's alarm state.
This would result in a condition where no spans were marked as the
"master" and so the core timer was handling conferencing. The core
timer runs by default at 4ms and most board drivers run at 1ms
intervals, but a channel currently only buffers up 2ms of data when
conferenced. Therefore, 2ms of audio from a board was continuously
dropped from the conference every 4ms by default.
This fixes a regression first introduced in 2.5.0 which was
specifically added in revision r9611 "dahdi: Do not locate new
master in interrupt context."
Internal-reference-ID: DAHDI-894
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Tested-by: Dennis Martinez <dmartinez@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10205 a0bf4364-ded3-4de4-8d8a-66a801d63aff
DAHDI currently waits a second before checking if a board driver is
calling dahdi_receive and switching to internal timing. Some versions of
Asterisk (I was looking at 1.4.42 when writing this) only wait 300ms for
a timer to expire when first starting and verifying that DAHDI is
properly configured. This can result in a
"ERROR[27673] asterisk.c: Asterisk has detected a problem with your DAHDI
configuration and will shutdown for your protection. You have options:"
message if asterisk is started soon after loading DAHDI.
This change sets the inital polling interval to the same as that used
during normal coretimer operation, 4ms. The interval will still be
slowed to 1 second if a board driver starts calling dahdi_receive().
DAHDI-892.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10200 a0bf4364-ded3-4de4-8d8a-66a801d63aff
When attaching software echocans to a channel, if there is a hardware
echocan available always give preference to them.
Revision 9995 "dahdi: Always attach hwec to a channel if available" had
an error where if a driver did not even support an option of hardware
echocan, dahdi-base would take that to mean there always was a hardware
echocan available on the channel.
DAHLIN-246
Reported-by: Michael L. Young
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10070 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Make sure that the call to dahdi_chan_unreg() in free_pseudo() is
protected by the registration_mutex, like the other calls to that
function.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-By: Oron Peled <oron.peled@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10056 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If set to true (default) a HWEC, if available on the channel, takes
priority over any software echocan configured in /etc/dahdi/system.conf.
This has historically been the default behavior in all released versions
of DAHDI that support module echocans.
Otherwise, hwec_overrides_swec is set to false, HWEC is chosen only via
the "echocanceller=hwec" directive.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-By: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10036 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In previous releases of DAHDI if dahdi_cfg attached a software echocan
to a channel and a hardware echocan was available, the hardware echocan
would be used instead of the software echocan.
Since the 2.4 branch was created a new feature was merged into
dahdi-linux where it was possible to mix software echocan and hardware
echocan on a channel. This required using "hwec" as the echocan in the
/etc/dahdi/system.conf file so that what was specified in the
configuration file is what was actually used.
This has resulted in users upgrading to the trunk of dahdi without
updating their /etc/dahdi/system.conf file and just suddenly not using
any hardware echocans any longer.
The capability to mix software and hardware echocans on a span will be
revisted when running dahdi_cfg on any preexisting configuration files
doesn't just silently turn off hardware echocan.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9995 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reverts commit r9891 and is part of two commits to revert all the
timer changes.
Grouping the timer into rates did not allow a timers rate to be changed
after another thread is already blocked on the poll call
The problem that was reported was if a sip call was made to a DAHDI
channel and the sip call was disconnected before answer, the DAHDI
channel would never stop rining.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9991 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reverts commit r9937 and is part of two commits to revert all the timer
changes.
Grouping the timer into rates did not allow a timers rate to be changed after
another thread is already blocked on the poll call
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9990 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This defines a NULL value for the name of an echocan as invalid. This
will allow dahdi_genconf to probe for the presence of a hardware echocan
on a channel by trying to attach one. If there is not a hardware echocan
available DAHDI_ATTACH_ECHOCAN ioctl will return -EINVAL if 'hwec' was
specified as the name of the echo canceler now.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9943 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Not quite ideal, but this seems to be the most straightforward way to
know when someone is trying to monitor the preec stream on a channel.
This callback allows the board driver providing the span an opportunity
to setup the hardware preecho monitoring as needed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9942 a0bf4364-ded3-4de4-8d8a-66a801d63aff
dahdi_ec_chunk is the function that saves the received audio and places
a signed linear copy of it in the pre echocanceled buffer on the
channel. By splitting the input and output of this function into two
parameters, a driver that can provide separate pre and post ec streams
can pass them independently to DAHDI, without worrying about DAHDI
overwriting a stream that may have already been echocanceled by the
hardware.
Previously, the dahdi_ec_chunk interface took a received audio buffer
and overwrote it after canceling the echo. Now the input and output
from the function are broken up in order to support hardware echocans
that have a different preechocan stream.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9941 a0bf4364-ded3-4de4-8d8a-66a801d63aff
