Also makes it safe to unregister a dynamic driver when there aren't any
open channels on the dynamic spans.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9580 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This allows the pvt member to be set under lock without holding the lock
through the call to create destroy.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9578 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Running in tasklets does not work well when dahdi doesn't have a span that is
acting as the master. In this case, process_masterspan is being called in
system timer that may not be running at 1ms intervals. The end result is that
the dynamic_run function isn't called for every chunk processed, and there is
data loss.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9577 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Dynamic spans that are unable to provide their own timing, like dahdi
local spans, typically derived their timing source from
dahdi_dynamic_ioctl(0,0) call in process_masterspan.
This change uses the sync_tick member of dahdi_span_ops instead so that
dynamic operations do not happen on a span until it is fully registered.
Also removes the check for dahdi_dynamic_ioctl in process masterspan for
those users that never load a dynamic span.
This was originally suggested in a comment on:
(issue #13205)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9576 a0bf4364-ded3-4de4-8d8a-66a801d63aff
2.6.9 is the earliest kernel version currently supported by DAHDI.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9575 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Move the try_module_get/module_put calls from the various dynamic
drivers into the "core" dahdi_dynamic.c file itself. This way, a
reference count can always be held while calling through the function
pointers. This is enabled by adding an .owner field to 'struct
dahdi_dynamic_driver'.
Dynamic spans are also unique in dahdi in that they require a "dahdi_cfg
-s" to stop them and release the references on the modules. This is
counterintuitive. This change makes sure they are reference counted just
like other spans and on driver unload, if there aren't any open handles
from userspace, they will take care of unwinding themselves.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9573 a0bf4364-ded3-4de4-8d8a-66a801d63aff
dahdi_dynamic can be converted to use kernel idiomatic reference
counting since DAHDI only supports 2.6.9+ kernels now.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9571 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The return value from the transmit callback function was not used
anywhere, and is now removed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9570 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Replaces all the 'z' references to 'd' as appropriate and cleans up any
formatting problems that popped up as a result. The intent here is to
reduce confusion in the future as someone may wonder what the 'Z's refer
to.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9567 a0bf4364-ded3-4de4-8d8a-66a801d63aff
It's possible for dahdi_dynamic_loc spans to be "peered" before the
dahdi_span is fully register. Do not call dahdi_dynamic_receive on any
peers before they are fully registered.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9566 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is a trivial formatting change in order to not introduce any warnings.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9565 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The memory saved by using a singly linked list does not, in my opinion,
outweigh the benefit of using the standard kernel macros.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9564 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Hopefully will eliminate any questions about what the 'z's are supposed
to represent.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9562 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This file is now in drivers/dahdi/voicebus folder. This file should
have been removed when the Gpak API was moved out of the individual
board drivers.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9559 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is a very slight performance improvement. Eliminating the need to
save the IRQ flags is probably more of a boost than grabbing and
releasing the reglock.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9558 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Mostly linux/errno.h was included more than once.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9557 a0bf4364-ded3-4de4-8d8a-66a801d63aff
dahdi/wcb4xxp driver used with Digium Wildcard B410 quad-BRI PCI card
unable to communicate with another ISDN device (ISDN phone, another port
of B410). It appears that B-channels are capable to transport data, but
D-channel is not.
Debug output added into the driver shows that packets are transmitted to
the D-channel, but no packets are received. Further investigation shows
that no interrupts received from Rx FIFO associated with D-channel,
although packets are delivered to the FIFO. I've found that problem is
in improper usage of chan->chanpos while indexing the fifo index
(bspan->fifos): chanpos starts from 1 and fifos starts from 0.
Therefore, garbage read instead of fifo number.
(closes issue #14834)
Reported by: vvv
Patches:
dahdi-linux-complete-2.2.0-rc1.patch uploaded by vvv (license 741)
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9555 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Instead of using pci_set_drvdata embed the 'struct voicebus_operations'
directly in the context so we can use container_of to find the context.
This resolves a problem where the 'remove_one' callback gets an invalid
pointer to 'struct t1' if the VPMADT032 is in the middle of a reload
when the module is unloading. DAHDI-783.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9554 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is instead of initializing the waitq each time the channel is
opened or closed.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerreicks <rmeyerreicks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9549 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since we've now switched to wait_event_interruptible calls, we have a
condition that we can check when we're awoken. This allows us to
combine the separate wait queues into a single queue.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerreicks <rmeyerreicks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9548 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Makes it a little more clear what it is we're really waiting for.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Russ Meyerreicks <rmeyerreicks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9547 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is a cleanup patch to make it a little easier to see what the bits
mean.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9543 a0bf4364-ded3-4de4-8d8a-66a801d63aff
There are some platforms where the read-line multiple transaction causes
packets to be dropped in the voicebus pipeline. The only observable
behavior is that packets just go "missing" in the pipeline. This also
only appears to affect PCI cards.
A typical 'symptom' of this problem is you may see IRQ misses increasing
without any corresponding "bumps" in latency in the kernel message log.
Normally, IRQ misses are correlated to latency bumps since that is an
indication that the host was not able to service the card interrupt in a
timely fashion. DAHDI-510 DAHDI-774
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9542 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The 'pdev' member already contained a pointer to what 'dev' was pointing
to. Also ensure most of the changed lines are under 80 characters.
There are two lines that are were too deeply nested to do anything
sensible.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9540 a0bf4364-ded3-4de4-8d8a-66a801d63aff
rwlock is slower than normal spinlocks and this lock is rarely contended
for. Also noticed that the vpmadt032_module_init function is now (was
already) redundant since all the elements initialized in it were already
initialized.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9538 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The mode module parameter is only acted on during module initialization.
We shouldn't allow anyone to change it after the driver is already
loaded.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9537 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Span registration is the last step in during initialization and it
should be the first on unregistration. I also was hit by this when
looking at adding other members to the span and made the assumption that
the span was in a consistent state during unregistration.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9536 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This reduces the chance that another interrupt will interfere with the
recovery process. Otherwise it is possible that the hardware advances
past the position that we think it is currently at.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9535 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Reading 0xffffffff from the registers is a different error than just not
coming out of reset. Add a little extra debugging information.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-By: Russ Meyerriecks <rmeyerriecks@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9534 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes a regression introduced in r9510 which saves a pointer to the ops
member of a channel's span before checking if the channel is a pseudo.
Psuedo channels do not have spans.
(issue #18463)
(issue #18422)
Reported by: alecdavis
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9530 a0bf4364-ded3-4de4-8d8a-66a801d63aff
I apparently forgot all about HPEC when updating the echocans for the change
in the factory and echocan ops structures related to echocan naming. The HPEC
wrapper should now be up to date with the rest of DAHDI.
Signed-off-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9526 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Changed the echocan factory name to a function (get_name) called to get the
name. This allows a factory to return a different name when being called in
reference to a channel such as in the case of hardware echo cancellers. To
further accommodate this change for HWEC, a new echocan_name function was
added to the span ops struct and is used in hwec_factory in dahdi-base for
all cards that support hardware echo cancellation.
Signed-off-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9524 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This field was redundant and was only used in places where the factory's name could be used.
Signed-off-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9523 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Remove the code that allowed hardware echo cancellation to automatically
override software cancellation and prevented SWEC from working at all on a
card if HWEC was installed. All EC now uses the standard modular EC interface.
Additionally, the "SWEC" identifier on channel lines in /proc/dahdi has been
changed to "ECTYPE" to avoid confusion.
Signed-off-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9521 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change adds an echocan factory to dahdi-base that will allow hardware
echo cancellation to use the same interface as the current software echo
cancellers. The additions in this commit will not have any effect until the
current HWEC mechanism is removed.
Signed-off-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9520 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The loopup/loopdown T1 maintenance feature in the single through quad-span
drivers now function properly, according to AT&T TR54016, by sending a
full rate pattern down the line. T1.403 ESF/Data Link patterns are not
supported currently.
Also grouped all the maint reset register clears under a single irq lock
to crank the performance up past 11.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9516 a0bf4364-ded3-4de4-8d8a-66a801d63aff
DAHDI_MAINT_LOOPSTOP is being removed due to the redundancy with
DAHDI_MAINT_NONE. Also removing some timing logic, as amount of time a
loopup or loopdown signal is held on the line, is now defined in
userspace with dahdi_maint.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9515 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The dahdi_span->maintq wait queue was very old and not being used so it
has been removed.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom..com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9514 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The wcte12xp does all the checking for alarm in a user space workqueue.
Most of this time is spent sleeping waiting for reads from the framer to
complete. Tasks in uninterruptible sleeps are added to running tasks
for the purposes of calculating load average. This change makes the
sleeps interruptible so as to not affect the load average as much.
For example, the following command will load and configure the driver and
then print the load average every 10 seconds.
]# modprobe wcte12xp && dahdi_cfg && ((x=12)); while [[ $x -gt 0 ]]; do cat
/proc/loadavg; sleep 10; let x=$x-1; done
With this change:
0.29 0.10 0.02 1/101 29945
0.24 0.10 0.02 1/101 29967
0.20 0.09 0.02 1/101 30019
0.17 0.09 0.02 1/101 30041
0.15 0.09 0.02 1/101 30062
0.12 0.08 0.02 1/101 30085
0.10 0.08 0.02 1/101 30107
0.09 0.08 0.02 1/101 30129
0.07 0.08 0.02 1/101 30151
0.14 0.09 0.02 1/101 30173
0.12 0.09 0.02 1/101 30195
0.10 0.08 0.02 1/101 30217
(and I've seen it get down to 0.0)
Before this change:
0.57 0.22 0.07 1/101 31920
0.48 0.21 0.07 1/101 31942
0.48 0.22 0.07 1/101 31964
0.48 0.23 0.08 1/101 31986
0.41 0.22 0.07 1/101 32008
0.42 0.23 0.08 1/101 32030
0.43 0.24 0.08 1/101 32054
0.45 0.25 0.09 1/101 32076
0.45 0.25 0.09 1/101 32098
0.46 0.26 0.10 1/101 32120
0.47 0.27 0.10 1/101 32172
0.39 0.26 0.10 1/101 32194
(closes issue #18142)
Reported by: foxfire
Tested by: foxfire
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9512 a0bf4364-ded3-4de4-8d8a-66a801d63aff
