Without digging into the specifics, it looks like Red Hat Linux 5.9
removed the hex_asc definition that was previously used to determine
if the bool definition was backported.
We can simply use the RHEL_RELEASE_CODE now since we do not support any
releases before the 5 series now.
Reported-By: Vladimir Mikhelson
Internal-Issue-ID: DAHLIN-312
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Don't run the pre- and post-unregister hooks on a non-phone XPD
(practically: the echo canceller). This fixes a panic with manual
'dahdi_registertion off' as it is now called for the whole device
(regression of 2.6.x).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10735 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* UMH_WAIT_PROC semantics (and value) was changed from enum to
a bitmask (via #define)
* This constant was missing from kernels older than 2.6.23
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10692 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* This is a minimal convertion -- everything compiles and looks OK.
* We print a warning for spans registering without a spantype.
* Low-level drivers may later want (but not required)
to fold their internal representations to this canonical
representation -- it will save code and make it more readable.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10683 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Previous commit (r10649) included an incorrect version. Including full message
from that commit for the description.
rev. 10502 of the FPGA firmware for the new E-Main rev. 4 fixes a potential
issue when used on Xorcom XR1000 systems: an issue with the power supply may
cause the unit to reset.
Note that there is no issue with previous models, with a normal setup of an
Astribank, or other XRx000 systems.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10652 a0bf4364-ded3-4de4-8d8a-66a801d63aff
rev. 10502 of the FPGA firmware for the new E-Main rev. 4 fixes a potential
issue when used on Xorcom XR1000 systems: an issue with the power supply may
cause the unit to reset.
Note that there is no issue with previous models, with a normal setup of an
Astribank, or other XRx000 systems.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10649 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Adds a new parameter, 'lower_ringing_noise', to module xpd_fxs.
* Makes the "power-down" behaviour that was added
in upstream svn r10478, switchable in runtime.
* By default (false), makes the vbat_h behave like it did
before the power-down change.
- I.e: vbat_h is held throughout the ringing period (during
both ring-up/ring-down)
- So this patch revert part of r10478
* When switched to true, activate the "power-down" behaviour.
- I.e: vbat_h follows the ring-up/ring-down.
- This behaviour lowers the noise caused by group ringing of
FXS channels in the same unit, but causes problems with CallerID.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10574 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* In do_chan_power() make vbat_h changes atomic.
* As a result we can ignore duplicate requests.
This will allow cleaner logic in the next commit.
* Added proper debug messages.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10573 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Remove a mostly harmless 0x1A (^Z) at the end of the file. If you
add a NL after it, it breaks the firmware loading.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10550 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The Makefile changes needed to install the two new files.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10536 a0bf4364-ded3-4de4-8d8a-66a801d63aff
USB firmware (USB_FW.201.hex 10402) and FPGA firmware
(FPGA_1161.201.hex 10480) with support of the new E-Main 4 Astribank
mainboard.
(This was accidentally labeled as 'E-Main 3' in some previous commit
messages)
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10535 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes an issues with the 6FXS/2FXO module: if an extra FXS or FXO module
is added to a system with such a module, an excessive number of port
licenses was accidentally required (as if the 6FXS/2FXO module required
8FXS/8FXO licenses).
Internal-Issue-ID: #1371
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10534 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Upstream commit bd77c047 "module: struct module_ref should contains long
fields" changed the return of module_refcount from int to unsigned long. This
change eliminates a warning from the string format specifier.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10485 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Eliminates warnings that are a result of upstream commit 72db395ffa
"module_param: check that bool parameters really are bool."
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10484 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Rotate the channels table in /proc/xpp/XBUS-*/XPD-*/fxs_info
- This way we don't overflow 80 columns
- Can also add more info items per-channel
* Linearize LED output for easier grep'ping
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10479 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Now every linefeed control command which is not RING'ing
powers-down the SLIC. This reduce audible noise when
several channels are ringing.
* Simplify code by removing redundant calls to do_chan_power()
before linefeed_control()
* Manage vbat_h state so we skip do_chan_power() calls when
there isn't a state change
* Export vbat_h state to /proc/.../fxs_info
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10478 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* If a DAHDI_AUDIO_NOTIFY is issued, offhook the channel
(added to BRI).
* If D-channel is closed, onhook all channels (added to PRI)
* If a clear channel is closed and the D-Channel is not
open (e.g: with patgen/pattest), onhook this channel
(added to both BRI and PRI)
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10476 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* A driver reload should reset Astribank hardware
* This patch send an SPI reset after we get AB_DESCRIPTION reply from Astribank
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10474 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This patch removes support for kernel versions < 2.6.18, as those are
not actively supported in any major Linux distribution (except RHEL4,
which is in the "extended" support level of the product life cycle).
This removes much of the more #ifdef-rich parts of the code.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10472 a0bf4364-ded3-4de4-8d8a-66a801d63aff
USB_RECOV.hex, rev. 9760. It may be used to recover from certain
issues of the USB controller of the Astribank (when an Astribank
is not detected as such) by Support staff.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10455 a0bf4364-ded3-4de4-8d8a-66a801d63aff
A slightly newer firmware (Xorcom rev. 7107) for older (non Astribank
II) Astribank modules. Was accidentally left uncommited. Includes minor
bug fixes.
No change for any relatively recent (Astribank II) Astribank.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10443 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Wrap in do {} while(0)
* Move closer to its use (it's #undef'ed anyway after this section)
* Also re-organize line-breaking in the same code section
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10434 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Manually place EXPORT_SYMBOL() after symbols (or at end of functions).
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10431 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Synchronize some changes from out internal tree:
* Fix a few of the places where indent did a lousy job.
* sparse did not like using the const MAX_ARGS as an index. Make it a define.
* Incorrect header included in card_fxs.c (doh!).
* One more funciton to statify.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10429 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* If dahdi_register_device() failed, not all resources were freed.
When dahdi_unregister_device() was called later (during driver
removal) a panic was caused.
* Add proper error handling for possible failures in
xbus_register_dahdi_device():
- new xbus_free_ddev() safely free an xbus->ddev
- This is called from all failures points.
- It is also called from xbus_unregister_dahdi_device()
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10410 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* A bug was introduced during migration to dahdi_device code:
http://svnview.digium.com/svn/dahdi?view=rev&rev=10273
* Marking XPDs as non-functional (card_present=0, XPD_STATE_NOHW)
was moved from xbus_request_removal() into xpd_dahdi_preunregister()
* As a result, unregistering an Astribank, made it non-functional
so trying to re-register it later caused errors (e.g: "Cannot open"
error message from xpp_open())
* This fix move XPD deactivation into the proper location (during
xbus_deactivate()
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10409 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* We need to split the BRI D-Channel (HDLC) frames to smaller packets,
limitation of the FPGA.
* This changes batches BRI D-channel packets of the same HDLC frame to a
single XPP frame.
* Avoids an accidental fragmantion in case we were delayed for a few ms-s.
* Also improves efficiency.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10390 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* The zero lenth case (Magic request) was split into
send_magic_request() function. It was not possible
to move it into card_bri.c, because it is called
directly from the general interface we provide for
register read/write via sysfs/proc.
* The normal case (send_multibyte_request) was moved from
card_global.c into card_bri.c
* This sets the stage to enable bundling of multibyte
packets into frames (like we do for PCM).
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10389 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Now that legacy BRISTUFF code is gone, some wrapper
functions became trivial. Removed these wrappers
and inlined their contents.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10388 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This is also a work around the bug fixed in the previous commit.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10384 a0bf4364-ded3-4de4-8d8a-66a801d63aff
module_put() that was added while developing the sysfs code. The real
module_get()/module_put() pair were already removed at the time of
developing code for this branch. It was only triggered when using a
system with more than 32 (MAX_BUSES) Astribanks.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10383 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Use similar caculation as in the PRI module:
* Save timing_priority from spanconfig and
elect syncer when spanconfig is called.
* Create custom timing_priority() function that returns
the value or error if span is disconnected.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: : Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10373 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* We must not block PCM during from 'search_fsk_pattern' channels.
* We must vmwi_search() not only on FXS_LINE_POL_ACTIVE, but also during
'neon_blinking' -- so we notice the message to turn it off.
* Also added 'search_fsk_pattern' and neon_blinking to /proc/.../fxs_info
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: : Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10372 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Restores the pri_protocol attribute of the XPD node in SysFS to be
writable. Fixes a minor regression from the pinned-spans fix, similar to
r10334.
* This attribute was made R/O in digium r10280 as part of the
pinned-spans changes:
- The E1/T1 settings were changed via new set_spantype() method
which was called from dahdi when the 'spantype' dahdi attribute
was written to.
- This fails our init_card_4_* trying to write E1/T1 into our private
attribute.
* Restored our old code (with minor modifications) so we
can set E1/T1 the old way (writing to our 'pri_protocol' attribute)
as well as the new way (when it will be used eventually).
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10347 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Force some reserved bits to really be 1 in E1 mode (otherwise
terrorists will win).
(Closes issue DAHLIN-264)
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10346 a0bf4364-ded3-4de4-8d8a-66a801d63aff
A length of 1000 commands is not enough is some cases with CAS.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10341 a0bf4364-ded3-4de4-8d8a-66a801d63aff
An extra fix that was accidentally not included in r10013. Minor bug fixes.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10337 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This restores a somewhat limited functionality of the "span"
write interface in the SysFS node of the span, broken by the
pinned-spans code.
* PROBLEM: dahdi-linux pinned-spans should work with existing dahdi-tools
specifically the dahdi_registration tool.
* As a result, we should still be able to control dahdi registration
order. However, registration is now in complete devices and not spans
* Restored dahdi_autoreg=[0/1] xpp module parameter:
- It now refers to complete astribanks and not individual spans
* The xpp module sysfs "span" attribute:
- Implemented write method (for dahdi_registration tool)
- The first write of [1/0] to this attribute, registers/unregisters
the complete astribank
- Further writes are ignored (with DBG messages)
* Also, implemented new xbus_is_registered() function
* Once the new dahdi-tools are merged, we should turn deprecation
messages from DBG() to NOTICE()
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10334 a0bf4364-ded3-4de4-8d8a-66a801d63aff
USB_FW rev 9964: includes a few stability bugfixes.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10323 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The NOTOPEN span alarm flag is set at span unassignment time.
* It needs to be cleared when the span is reassigned.
* That is: only if the span is actually connected.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10302 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* An xbus transport now have a "model_string" member
* The xpp_usb driver fills this with "usb:<idVendor>/<idProduct>/<bcdDevice>"
* It is passed via environment to the "init_card_<type>_<protocol>" scripts
* The FXS script uses this to condition two registers according to
the power supply model.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10300 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* With pinned-spans all spans are registered to dahdi with the
device (and assigned later)
* So this parameter cannot function anymore
* Also remove the (now) empty xpd_post_init() function.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10284 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Otherwise, a failed unit initialization (e.g: when init_card_?_?? fails)
causes a panic
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10282 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Reparent astribanks below their USB transport
* This way their location can be derived from their hardware
hierarchy.
* The tradeoff is that once USB hardware is disconnected, there
is no sysfs visibility of the astribank object even if it
cannot be release yet due to open channels by asterisk
* Thus, we'll need to migrate to "surprise removal" of dahdi
devices...
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10281 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Implement pri_set_spantype() method
* Refactor code from PRI_card_dahdi_preregistration() into
a new apply_pri_protocol().
- It is now called from both PRI_card_dahdi_preregistration()
and set_pri_proto()
- It now also sets span name + description
* Remove old pri_protocol_store() method (pri_protocol is now RO)
* Added pri_protocol_bystr() method (maybe promote it to DAHDI?)
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10280 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This exposes dahdi devices in sysfs and also exposes attributes that
will allow user space to control the registration order in spans. This
facilitates loading drivers out of order yet keeping consistent
span/channel numbering, which in turn will eventually allow the
blacklist for DAHDI drivers to be removed. The default behavior,
controlled with the auto_register module parameter on dahdi is to number
the spans / channels in order like is currently done. So this change
does not introduce any new behavior by default.
* Writing (anything) to this attribute returns the span to its
unassigned state
* Fix dahdi_chan_unreg() echocan refcount
* Add safeguard against duplicate unassignment to _dahdi_unregister_span()
* Remove the span from device_node list, only in dahdi_unregister_device()
and not in dahdi_unregister_span()
* Free allocated span->span_device in span_sysfs_remove()
[is it safe?, didn't cause problem so far...]
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
dahdi: Add "hardware_id" dahdi_device attribute.
- The "hardware_id" does not change with device location (e.g: when a PCI
card is moved from one slot to another).
- Not all devices have this attribute. It is legal for it to be NULL (that
is the default for all low-level drivers that do not set it explicitly).
- When "hardware_id" is NULL, the sysfs attribute value is "\n"
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10275 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Increasingly, spans are implemented by devices that support more than a
single span. Introduce a 'struct dahdi_device' object which explicitly
contains multiple spans. This will allow a cleaner representation of
spans and devices in sysfs since order of arrival will not determine the
layout of the devices. This also gives the core of dahdi a way to know
the relationship between spans.
This generalizes similar concepts that were previously xpp specific. The
conversion of the xpp code was almost entirely done by Oron and Tzafrir.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10273 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This patch contains interim results while trying to make
device removal work correctly:
* XPP has protections to prevent dahdi unregistration while
channels are open -- they are now removed, so we can
unregister immediately.
* Handle processes in poll_wait():
- Wake them during dahdi_chan_unreg() after the channel
is gone (chan->channo = -1 or chan->file->private_data == NULL)
- Test in every wait_event_interruptible() that the channel
was not gone (chan->file->private_data)
- Return correct values (POLLERR | POLLHUP) instead of
some errno (would be important in the future if we
modify asterisk to respond correctly to this condition.
* Other issues:
- If unregistered channel is being polled, than call msleep() before
returning, to give other processes a chance (normally, asterisk
has RT priority)
- Call close_channel() from dahdi_chan_unreg() so it releases
related tonezone
* There is still a horrible race hidden by msleep(20) in
dahdi_chan_unreg()
force close channels from dahdi_chan_unreg():
* Mark them via DAHDI_FLAGBIT_OPEN
* Call low-level driver close() method if available
* What about other closing activities?
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10270 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* 'D' DTMF digits were accidentally discarded with the notice message:
"Bad DTMF value 0. Ignored".
* No need for an odd 1-based translation table anymore - it's 0-based.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10209 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Bug sympthoms: wrong FSK VMWI sent few seconds after
offhook. That was caused because the driver kept
polling the (physically unconnected) digital inputs.
[note: a workaround for drivers without this patch
is to zero the 'xpd_fxs.poll_digital_inputs' parameter.]
* Also, the digital_inputs/digital_output masks were
calculate using a different condition.
* Now we determine number of channels, digital inputs and
digital outputs in a single place and use this info
later to calculate the correct masks.
* We poll only if there are digital_inputs
* We added a sanity check in process_digital_inputs, so
we get a notice if it's called on an xpd without digital
inputs (e.g: hypothetic firmware bug).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10202 a0bf4364-ded3-4de4-8d8a-66a801d63aff
New firmwares to handle the new 2FXS/6FXO module.
FPGA_1161.hex, PIC_TYPE_1.hex, PIC_TYPE_2.hex of internal rev. 9732
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10179 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Astribank II FPGA firmware rev 9605. Includes two bug fixes:
* Error in checking EC licenses when the license was for exactly 64 or 128
channels.
* Proper handling of a slave FXO Astribank (in line with the quirks
handling from r10019).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10099 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Required by CAS in latest (2.5) DAHDI versions.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10055 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This avoids a nag about a meaningless single-bit signed int.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10054 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If the CPU becomes overly busy, merely printing the "Overflow in the
recieve_queue" messages becomes CPU-intensive on its own right.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10052 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If the OCT6104E-256D.ima Octasic firmware was downloaded to the build
directory, install it over with the rest of the firmware files.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10038 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This adds module parameter 'ring_trapez'. When set, the wave form of
the ring tone is set to be a trapezoid, rather than sine. Thus making
the ring stronger.
This is a boolean parameter of the module xpd_fxs. Takes effect at the
beginning of the next ring.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10022 a0bf4364-ded3-4de4-8d8a-66a801d63aff
gcc 4.6 complains about variables that are assigned values but then
never used.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10020 a0bf4364-ded3-4de4-8d8a-66a801d63aff
In some cases the hardware echo canceller cannot be used. Mostly related to
an FXO module.
* FXO module if the first module is BRI or PRI
* FXS module if the Astribank has another FXO, no PRI/BRI, and is a sync
slave.
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Acked-By: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10019 a0bf4364-ded3-4de4-8d8a-66a801d63aff
New Astribank II FPGA firmware and USB firmwares that add support for the
hardware echo canceller module.
Note that due to a bug in previous FPGA firmwares, an Astribank with such
older firmware and with a hardware echo canceller module will not have any
functioning audio at all.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@10013 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* xpd_echo (card_echo.c) - a module to handle an Astribank hardware echo
canceller module.
* All other XPDs are now of type 'telephony_device'. Only a telephony device
XPD provides a span to register.
* The EC module will typically show up as XPD-40 and will always show up as
Unregistered in 'dahdi_hardware -v'
Signed-off-by: Oron Peled <oron.peled@xorcom.com>
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9993 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This change ensures that the dahdi_span_ops callbacks are not called
with any spinlocks held, and that the module is pinned in memory, and
also passes the struct file * pointer to the callbacks.
Passing the file pointer to the callbacks allows the board drivers to
check any flags on the file descriptor used to configure the
span/channel. The intent here is to allow dahdi_config to open the
/dev/dahdi/ctl file in a non-blocking mode in case there is a lengthy
processes that needs to happen as part of configuration.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9940 a0bf4364-ded3-4de4-8d8a-66a801d63aff
gcc-4.6 now warns about variables that are set but never used. Clean up
unused variables everywhere except the oct612x subdirectory.
The oct612x should go in a separate patch in case that needs to be
pulled out into a separate project again.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9929 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Some older Asttribanks had an empty label string. They should be ignored
when testing for a duplicate label at device probe time.
While we're at it, reduce panic level in the notice.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9925 a0bf4364-ded3-4de4-8d8a-66a801d63aff
XPP_DEBUGFS code was some code used to send BRI D-Channel data
through debugfs for, well, debugging. Unused in recent years.
Time to remove.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9917 a0bf4364-ded3-4de4-8d8a-66a801d63aff
OLD_PROC marked old and unused code that was used for writing to procfs.
It has long ago been replaced with different sysfs interfaces. Time
to remove it.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9916 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Folded XPD_STATE() "protocol method" into the card_state() method.
It was only called from these (otherwise empty) methods.
Also it is not a "protocol method" for a very very very long time.
Signed-off-by: Oron Peled <oron@actcom.co.il>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9715 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Caller to CALL_XMETHOD() no longer need to explicitly pass xbus
(calculate xpd->xbus)
* Create CALL_PHONE_METHOD() similar to CALL_XMETHOD() -- inlining
the extra parameters (more readable)
* Reverse parameter order in PHONE_METHOD() and CALL_PHONE_METHOD()
to be consistent with XMETHOD() and CALL_XMETHOD()
* Rename XPD_STATE phonedev method to card_state:
- Consistency with other phonedev methods.
- These calls now Wrap internal calls to XPD_STATE protocol HOSTCMD
in PRI, BRI, FXS, FXO
Signed-off-by: Oron Peled <oron@actcom.co.il>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9706 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Add IS_PHONEDEV(xpd) macro
* Reject dahdi_register_xpd()/dahdi_unregister_xpd() for non-PHONEDEV
* Make sysfs 'offhook' attribute contain '\n' if empty (no channels)
* Skip PHONEDEV related xbus_tick() parts -- we still want to process
the end of it for the card_tick() calls.
* Remove BUG_ON() for missing phoneops
(also remove old duplicate test for XBUS_IS...)
* Call XPD_STATE method only for PHONEDEV XPD's
Signed-off-by: Oron Peled <oron@actcom.co.il>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9705 a0bf4364-ded3-4de4-8d8a-66a801d63aff
* Allow having XPDs that represent a device that is not a span.
* Refactor all span related data from 'struct xpd' to 'struct phonedev'
* Refactor span related methods into 'phonedev->phoneops'
* Refactor phone related initialization into phonedev_init()/phonedev_cleanup()
Signed-off-by: Oron Peled <oron@actcom.co.il>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9704 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Since the return value is not defined/used just return void.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9587 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Mostly linux/errno.h was included more than once.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9557 a0bf4364-ded3-4de4-8d8a-66a801d63aff
DAHDI_MAINT_LOOPSTOP is being removed due to the redundancy with
DAHDI_MAINT_NONE. Also removing some timing logic, as amount of time a
loopup or loopdown signal is held on the line, is now defined in
userspace with dahdi_maint.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9515 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The dahdi_span->maintq wait queue was very old and not being used so it
has been removed.
Signed-off-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom..com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9514 a0bf4364-ded3-4de4-8d8a-66a801d63aff
If the span reports that it supports hooksig, DAHDI may fail to use RBS.
So remove a call to that stub function.
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9506 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This fixes an annoying, though harmless issue: if Asterisk decides to send
voicemail messages to a channel (CAS, configured as FXS), We can't do
anything useful with them. So ignore them to avoid scary-looking messages
(from report_bad_ioctl()).
Signed-off-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9505 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Using semaphores as mutexes was removed from the kernel in 4882720b267b.
Just use straight semaphores now. 'DECLARE_MUTEX()' -> 'DEFINE_SEMAPHORE()'
and 'init_MUTEX()' -> 'sema_init()'.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
LKML-Reference: <20100907125057.562399240@linutronix.de>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9464 a0bf4364-ded3-4de4-8d8a-66a801d63aff
Fixes a regression singce r8873: if pri_protocol is not explicitly set
(in /etc/dahdi/xpp.conf) and the device has (licences for) less than 4
"PRI" (E1/T1) ports, the initialization script will attempt to read from
a non-existing SysFS file, and bail out, resulting in a the device
failing to initialize.
For those non-existing ports we can just skip that part of the
initialization. So we just skip it.
Work around: explicitly set pri_protocol to E1 or T1, as needed.
Xorcom Rev: 8047. Ticket: 1334.
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9430 a0bf4364-ded3-4de4-8d8a-66a801d63aff
The check for DEFINE_SPINLOCK was spread throughout the source tree. If
not defined we can just define it in inlucde/dahdi/kernel.h. Now
include/dahdi/kernel.h is the only place that references
SPIN_LOCK_UNLOCKED (which breaks lockdep checking if DEFINE_SPINLOCK is
otherwise defined in the kernel).
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
Acked-by: Kinsey Moore <kmoore@digium.com>
Acked-by: Russ Meyerriecks <rmeyerriecks@digium.com>
Acked-by: Tzafrir Cohen <tzafrir.cohen@xorcom.com>
Review: https://reviewboard.asterisk.org/r/940/
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9411 a0bf4364-ded3-4de4-8d8a-66a801d63aff
This needs some more testing before it's on by default. If the card is
otherwise functioning, these messages may be confusing to the user. If
the card is not functioning, the driver can be reloaded with debug to
check for this condition.
Signed-off-by: Shaun Ruffell <sruffell@digium.com>
git-svn-id: http://svn.asterisk.org/svn/dahdi/linux/trunk@9205 a0bf4364-ded3-4de4-8d8a-66a801d63aff
