Firefox incorretly displays placeholder audio device labels in the audio
settings/echo test modal when audio is disconnected. This issue arises
due to two quirks:
- Firefox does not support the 'microphone' query from the Permissions
API, causing a fallback gUM permission check.
- Firefox omits device labels from `enumerateDevices` if no streams
are active, even if gUM permission is granted. This behavior differs
from other browsers and causes our `enumerateDevices` handling to
assume that granted permission implies labels are present. This
failed since we clear streams before resolving the fallback gUM.
We now run an additional `enumerateDevices` call in `AudioSettings` when
a selected input device is defined. This ensures `enumerateDevices` is
re-run when a new stream is active, adding the correct device labels in
Firefox and improving device listings in all browsers. We've also
enhanced error handling in the enumeration process and fixed a false
positive in `hasMicrophonePermission`.
This is a rework of the audio join procedure whithout the explict listen
only separation in mind. It's supposed to be used in conjunction with
the transparent listen only feature so that the distinction between
modes is seamless with minimal server-side impact. An abridged list of
changes:
- Let the user pick no input device when joining microphone while
allowing them to set an input device on the fly later on
- Give the user the option to join audio with no input device whenever
we fail to obtain input devices, with the option to try re-enabling
them on the fly later on
- Add the option to open the audio settings modal (echo test et al)
via the in-call device selection chevron
- Rework the SFU audio bridge and its services to support
adding/removing tracks on the fly without renegotiation
- Rework the SFU audio bridge and its services to support a new peer
role called "passive-sendrecv". That role is used by dupled peers
that have no active input source on start, but might have one later
on.
- Remove stale PermissionsOverlay component from the audio modal
- Rework how permission errors are detected using the Permissions API
- Rework the local echo test so that it uses a separate media tag
rather than the remote
- Add new, separate dialplans that mute/hold FreeSWITCH channels on
hold based on UA strings. This is orchestrated server-side via
webrtc-sfu and akka-apps. The basic difference here is that channels
now join in their desired state rather than waiting for client side
observers to sync the state up. It also mitigates transparent listen
only performance edge cases on multiple audio channels joining at
the same time.
The old, decoupled listen only mode is still present in code while we
validate this new approach. To test this, transparentListenOnly
must be enabled and listen only mode must be disable on audio join so
that the user skips straight through microphone join.
There's no rollback procedure in case a device switch fails right now,
nor does the code entrypoints that call the switching procedures wait
for resolution or failure before marking the new device as chosen. That
may cause inconsistent states in a couple of ways:
- No rollback: switch fails, audio is still on but no actual
microphone input is being transmitted
- Not waiting for resolutions: inconsistent chosen devices on failures
Device switching errors are also not surfaced to the end user
This commit:
- Adds device rollback and proper resolution/failure response
awaits to try and make the state a bit more consistent.
- Centralizes the input device switching code to be reused between
different bridges
- Centralizes device ID state management in audio-manager to try and
mantain them a bit more consistent across the board
- Surface device switching failures to the end user
- Guarantee device IDs are set to the session storage on all
appropriate scenarios
The initial selected output device in AudioSettings could be the wrong one if
the user's session had an output device ID already stored, but is joining on a
new session. That would cause the remote-media tag not to be updated with the
correct output device ID when it should (the service.js change)
The issue is tackled by guaranteeing the output device ID is set on all ends
when AudioSettings/AudioModal mounts.
public.media.showVolumeMeterInSettings => public.media.showVolumeMeter
public.media.simplifiedEchoTest => public.media.localEchoTest.enabled
Initial hearing state can be configured in public.media.localEchoTest.initialHearingState
New features:
- A simplified echo test mode that only does a local loopback (instead of
going to FS and back)
- A volume meter for microphone streams to the AudioSettings view
Those two features are experimental and disabled by default; see
public.app.media.simplifiedEchoTest and public.app.media.showVolumeMeter configs
Collateral changes:
- fix: localize fallback device strings in AudioSettings/DeviceSelector
- Refactor on some media stream utils to be re-usable across components
- Refactor in AudioSettings to keep gUM #uses stable.
* TODO: need to pass streams through AudioManager to avoid the surplus gUM.
- fix(audio): drop ScriptProcessorNode usage (deprecated)
* Used in volume meter for tracking - use hark instead
When joining breakouts, we now wait for the bridge to be loaded before
automatically start user's audio.
This problems happens only on fullaudio bridge
Allow listenonly users to change output devices
Fixed dynamic audio device change for firefox
Fixed shortcuts for audio join/leave
Show (with a bold font) the current selected device
[performance] Prevent calling mediaDevices.enumerateDevices every time we render
the selector. This adds a delay (~200ms, on my chrome setup) to render this component
[performance] Do not call enumerateDevices to search for new devices, instead we listen on mediaDevices.deviceChange event
Small refactoring and fixed a few errors that were being throw in browser's console
Fixed device selection when this is done in audio-settings modal
Fallback to default device when current device is removed
Truncate device name length
Renamed "Input","Output" labels to "Microphone","Speakers", respectively
Update eslint rule for accessKey
Currently this information is lost everytime breakout-room component is
unmounted, causing the panel to shows wrong information during next renders
Fixes#11333
After audio reconnection, a muted user would have it's microphone unmuted by default, unless muteOnStart is set to true. This fix this problem.
Fixes#9016
